Question about Pontiac Montana

1 Answer

How to tork the harmonic balancer pully - Montana Pontiac Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 4,977 Answers

If you have access to an air compressor and air tools then just run up the bolt tight with an air gun.if not then you need to keep the crank pulley from moving while you torq the balancer bolt however you can without causing any damage.

Posted on Apr 10, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The rubber on my crankshaft pully is worn and my pully is wobbleing can i tack weld it


That is not a pulley. that is the harmonic balancer and NO you cannot weld it.

Aug 09, 2014 | 1996 Toyota Carina

1 Answer

The big outside pulley on the harmonic balancer fell off


The Harmonic balancer is held on to the front of the crank shaft with a bolt. there are pullys pressed onto the harmonic balancer in rubber.If more pulleys are needed for more accessories they are bolted to the harmonic balancer.

Apr 20, 2013 | Cars & Trucks

1 Answer

The pully assembly for the serpentine on my 2004 santa fe has a loose pully, ie: it came apart when I pulled off the grime shield in the wheel hub, IDK which of the pullies this loose part connects to, and...


It sounds like the harmonic balancer came apart. This is a two part pulley seperated by a rubber gasket. The part itself is much less expensive at auto parts stores than the dealership but you may need to wait a few days for it to arrive as most stores won't have the part in stock. A picture of the harmonic balancer is below:

2004 SANTA FE HARMONIC BALANCER


10_1_2011_3_34_37_pm.jpg

Oct 01, 2011 | 2004 Hyundai Santa Fe

2 Answers

Location of crankshaft censer 2007 chevy cobalt


The Crank shift sensor is located in front of the motor in between the intake manifold and oil filter housing, nest to the knock sensor. Look on side cylinder block beside starter.you have to remove the starter to remove the crankshaft sensor. Hope this helps. Thanks for choosing Fixya, RJ

May 16, 2011 | 2007 Chevrolet Cobalt Coupe

1 Answer

Where is the crank sensor located on a 07 chevy uplander


the crankshaft postion sensor is always located either under the harmonic balancer pully aka crankshaft pully or mounted right outside the pully if yoiu need to change it keep in mind that you will need to to own or rent a harmonic balancer pully puller and a harmonic balancer pully installer kit both you can rent both at autozone fairly cheap and get all your money back when your done
job rating from 1-10 about a 3


hope it helps if so could you please leave me a 4 thumbs up feedback thank

May 12, 2011 | 2007 Chevrolet Uplander

1 Answer

What does the crank sensor look like for a 1999 chrysler sebring lxi?


just a piece of plastic its the only sensor it is located under harmonic balancer pully on most vehicles some are just right outside the harmonic balancer pully


if it helps please leave a good review thumbs up

May 08, 2011 | 1999 Chrysler Sebring

1 Answer

I have a 2003 Hyundai Tiburon 2.7L. Harmonic Balancer is loose. The car looses power. The serpentine belt comes off the pully. The vehicles starts but only the bottom pully turns I believe it is the...


sounds like the pully is spinning around the harmonic balancer the **** is broke i have same problem almost o rilley parts has one 50.00 bucks rent the tool to take it off and go to youtube to see how good luck

Jan 13, 2011 | 2003 Hyundai Tiburon

1 Answer

How come the harmonic balancer is not lined up with the other pullies and the belt keeps slipping off or breaking in the middle?


the harmonic balancer is bad they have a rubber bushing in them which goes bad and sets them off the rest of the pullys you will have to replace the harmonic balancer and that should take car of the problem if you have any other questions feel fre to ask hope that info helps

Nov 22, 2010 | 2002 Pontiac Grand Am

1 Answer

How do i replace the harmonic balancer on a 95 royale 88


Remove all belts and rad, use a pully puller to remove the belt pully, and then you need a special puller to pull the harmonic balancer.

Aug 12, 2009 | Oldsmobile 88 Cars & Trucks

1 Answer

Harmonic balancer


Is the pully on correct?

Aug 28, 2008 | 1988 Oldsmobile Toronado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...