Question about Chevrolet Celebrity

1 Answer

1986 chevy celebrity 2.8L. I need to see a picture of where the bolts are located to mount the starter.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Go to auto zone and get a picture of the starter on-line. Two bolts that go straight up on the drive end of starter, short one and a long one.

Posted on Apr 10, 2011

Testimonial: "thanks for the lead. appreciated "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove starter on 1984 chevy celebrity


According to manuals starter removal is dependent upon the engine type used however I looked at a 1984 Celebrity with 2.8 L X version enigne and both mog my repair manauals which toild me nothnig aobut the fiornt frame of htis vehicle being in the way of the starter mounting bolt nearest the engine hence it appered to me one woulde need to raise the engine if it could be raised enough or remoive the negine., If nyone have remoived thios startewr pelase let me know hw, okay/

Jun 13, 2012 | Cars & Trucks

1 Answer

1988 Chevy Tahoe Starter going out. Need to replace


Generally starters have 2 or 3 bolts and a thick wire coming from the battery and other miscellaneous connections.

You did not specify a vehicle that was on my list, i.e. 1988 Chevy Tahoe.

However, it may be similar to a Suburban R10:
REMOVAL & INSTALLATION The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
  1. Disconnect the negative battery cable at the battery.
  2. Raise and support the vehicle.
  3. Disconnect and tag all wires at the solenoid terminal. NOTE: Reinstall all nuts as soon as they are removed, since the thread sizes are different.
  4. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter. Fig. 1: Starter mounting location — 4.8L engines 84903021.gif
    Fig. 2: Starter mounting location — 4.3L and 5.0L engines 84903022.gif
    Fig. 3: Starter mounts — 5.7L and 7.4L engines 84903023.gif

  5. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck. To install:
  6. Position the starter and tighten all bolts as follows: R/V Series:
    • Thru-bolts: 40 ft. lbs. (54 Nm)
    • Bracket bolt: 30 ft. lbs. (41 Nm)
    • Nut (gas): 11 ft. lbs. (15 Nm)
    • Nut (diesel): 90 inch lbs. (10 Nm)
    C/K Series:
    • Thru-bolts: 35 ft. lbs. (45 Nm)
    • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
    • Nut (diesel): 75 inch lbs. (8.5 Nm)
  7. Reconnect all wires. Fig. 4: Disconnect the negative battery cable 87982p25.jpg
    Fig. 5: Remove the starter retaining bolts 87982p30.jpg
    Fig. 6: Remove the starter from the vehicle 87982p31.jpg
prev.gif next.gif

Jul 19, 2010 | 1984 Chevrolet Chevy

1 Answer

How do you change a 1986 chevy celebrity steering column?


  1. take off bottom dash cover
  2. bottom of colum has a bolt and nut that has to come off
  3. then theres 4 bolts holding colum up remove bolts colum will drop
  4. unplug electricalal conection
  5. pull colum out

Feb 09, 2010 | 1986 Chevrolet Celebrity

1 Answer

How do I replace my starter?


Open hood.
Disconnect negative (-) batter cable
Locate the starter (under vehicle).
Remove electrical connections. (be sure to remember/take a picture/ make a drawing/ or mark which wires go to what posts)
Remove mounting bolts.
Remove starter, replace with new starter
Install mounting bolts
Install electrical connections

Jan 06, 2010 | 1990 Chevrolet S-10 Blazer

2 Answers

I need to see a diagram of a 1986 chevy celebrity engine so I can find the fuel filter. I don't believe this is the original engine in this car.


The fuel filter should be inline just after the fuel tank , look under chasis next to but in front of the fuel tank , should be in a clamp bolted to the frame or unibody subframe in your case ... Hope this helps...

Sep 04, 2009 | 1986 Chevrolet Celebrity

1 Answer

How do i change an alternator belt on 1986 chey celebrity


You shouldn't have to... There is a large bolt on the front of the main pully. When you put the wrench on it, it will move that pully allowing you to put the belt on.

Apr 10, 2009 | 1989 Chevrolet Celebrity

1 Answer

Bad starter. how do you remove. how many bolts are there??


once you have located the starter ther are two bolts and two wires the bolts are located directly accross from eachother on each side of the starter the wires are on the back of starter hope i could help

Mar 23, 2009 | 1986 Chevrolet Celebrity

1 Answer

Trying to locate fuse block for 1986 chevy celebrity wagon


That should be under the dash on the drivers side hope this helps

Mar 19, 2009 | 1986 Chevrolet Chevy

1 Answer

Ignition Module Replacement for 1989 Chevy Celebrity 2.8 V6


First of all, number your wires before you pull them off. Pull the wires off, unplug the module. (You need a deep well swivel socket to get to the bolts). Also, make sure your battery cable is disconnected - being close to the starter wires. It's easier to get to from under the car. Make sure you use jack stands and be extra careful. Hope this helps. Phil

Jan 27, 2009 | 1989 Chevrolet Celebrity

1 Answer

Clicking noise when trying to start car,battery is ok, wont start


That Clicking is the Battery causing it not to Start. You need to Replace that Battery or at Least put a Charger on it for a Couple of hours to see if you can Salvage it for a While.

Jan 19, 2009 | 1986 Chevrolet Celebrity

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...