Question about 2004 Chrysler Crossfire

Open Question

2004 Chrysler Crossfire hood won't release. When you pull the release you can hear it pull but won't release.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 89 Answers

SOURCE: 2004 Mercury Grand Marquis Hood won't open

try getting another person to lift on the hood while you pull the release, the lift assist spring might have broken

Posted on Nov 06, 2009

  • 1986 Answers

SOURCE: The hood will not release to open. I released the

So I gather that the release inside the car has release the hood's primary catch, but the T handle is not release the secondary catch to allow the hood to fully open.

If this is the case, take some lithium grease or WD-40 (lithium grease is much better and lasts much longer) and spray it onto the catch assembly.

Try pulling on the T handle some more after a few minutes of the grease soaking in and see of that releases.

If that doesn't work, then take a long flat screw driver and press it against the catch gently hit the screw driver with a hammer (you should be trying to push the catch towards the driver's side of the car)
You may need someone to be pulling on the T handle as you hit the catch with a hammer. I actually had to do this with a jetta before....

Posted on Nov 20, 2009

  • 295 Answers

SOURCE: Stuck hood latch on 1996 chrysler concorde- Possible broken cable

take off the left front wheel and fender well. slice off the hood cable insulation get a hook too pull the wire have a buddy pull up on the hood while doing this. Should pop open then hope this helps u out.

Posted on Nov 23, 2009

smartr10U
  • 1305 Answers

SOURCE: engine hood wont open hood pull handle pulls out but wont release

Try pulling on the hood release, while someone else lifts the hood. If this doesn't work. You can access the underside of the hood release by taking the front grille out. If you look closely you'll see the retainer screws that can be removed from the front. Once the grille is out or loosened enougt to get your hand in behind, you can release the hood latch from the underside with a screwdriver and then repair the hood latch after you've opened it.

Posted on Dec 09, 2009

  • 1 Answer

SOURCE: Hood release won't open hood, can't open my hood

I had this happen to my 1999 Honda Civic. I took it to my mechanic and they had to pry the hood open by snapping the latch and then they replaced it.

Posted on Dec 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the Drivers Side Headlight (bulb?) for 1998 Chrysler LeBaron (there is a coolant reservoir right behind the light assembly under the hood :(


Raise the hood and look at the headlight assembly from the top, you should see a couple of pins to remove and pull them up...the headlight assembly should come out. then just remove the plug and replace the bulb

May 26, 2014 | 2004 Chrysler Crossfire

1 Answer

Crossfire hood release


Get underneath the front end with a long screwdriver and jimmy the mechanism.

Oct 24, 2013 | Chrysler Crossfire Cars & Trucks

1 Answer

2004 Chrysler crossfire won't go into gear please help ASAP!!


It's the brake pedal switch that has either a broken wire or needs to be replaced. They are cheap and only take about 15 to replace.

Jan 31, 2013 | Cars & Trucks

2 Answers

Can't remove light assembly from 2004 Chrysler Sebring Convert. I have removed the two screws but something appears to be stopping me from pulling forward. ideas?


There are 4 screws. Two are underthe hood. The other two can be accessed through the access hole in the fender well. It is usually easiest to remove the front wheel assembly so you can see in there.

Feb 23, 2011 | 2004 Chrysler Crossfire

1 Answer

Passenger side headlight assembly removal, is there more than 2 bolts, if so where


You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

  1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.



Dec 12, 2010 | 2004 Chrysler Crossfire

1 Answer

Need to replace headlight?


  • Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  • 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  • 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  • 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight I would replace them both sides if i were you
  • Dec 02, 2010 | 2004 Chrysler Crossfire

    2 Answers

    2004 chrysler crossfire resetting service light


    Disconnect negative battery post for 30 seconds & reconnect. This action will reset the car's computor & remove the light.

    Jan 07, 2010 | 2004 Chrysler Crossfire

    Not finding what you are looking for?
    2004 Chrysler Crossfire Logo

    Related Topics:

    229 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...