Question about GMC S-15

1 Answer

Removing rear axle seals for a 1986 S-15 Jimmy

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • GMC Master
  • 975 Answers

Pull the rear wheels,take off the diff cover,remove the 5/16 pin that holds the big pin,pull the big pin ,push in on the axles,remove the 2 c clips that are on the axles and slide the axles out.If the axle shaft is worn by the bearing,an axle -saver bearing is available. If the axle is ok just pull the seal ,drive the new one in and re-assemble.

Posted on Apr 10, 2011

  • Ronald lott Mar 18, 2015

    I've done all that I've even pulled the 1'1/4 nut off of the pinon shaft and that is the shaft I can't get out I'm using a 3lb slug and it will not come out what can I do

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are some tips on removing and replacing brake lines etc when replacing the rear end on 97 Dodge 1500


Held on by a bolt and two clips. Bend the clips and remove the bolt. Just be prepared to replace them if they are really rusty. If it were mine, I would pull the axles, Replace the diff and pinion and seal. Replace the axle bearings and seals, if the seals were leaking. If not leaking, just replace the seals.

Mar 06, 2016 | Dodge Cars & Trucks

1 Answer

I have a 97 GMC jimmy with a 4.3 v 6, 2 wheel


"Blue Devil Oil stop Leak", Used this in My 97 Jimmy, Also for my Rear main seal..various other leaks.. WORKED! Didn't believe it would..... Stopped all leaks. Every leak is diff. Depends on How bad of course, but well worth the try.Cheaper than pulling those Axles!, If it doesn't I do believe they will refund your $... Good Luck!

Oct 09, 2014 | 1997 GMC Jimmy

1 Answer

How do i change da rear other seal on the rearend of a 1985 chevy silverado


Replacing axle seals requires removing the differential cover,removing the spur gear bolt/shaft,removing the C clip,then sliding the axle out.You will have to press the bearing off of the axle to remove the seal,which usually will break the bearing(might as well replace it anyway on an '85).Removing and replacing the bearing should be done with a shop press.

Mar 30, 2012 | 1983 Chevrolet Silverado

1 Answer

2002 jeep grand cherekee rear axle seal removel do i need to remove c clips in rear to remove axle


No.....after removing the brake caliper and rotor, Unbolt the axle retainer plate from the axle tube flange. You need a slide hammer to pull the axle out.

Mar 19, 2011 | 2004 Jeep Grand Cherokee

3 Answers

I have gear oil coming out of right rear tire area


You have a leaky axle seal. Sometimes this is cause by the vent or breather being plugged. Sometimes they just wear out and another cause is bad bearings. Either way the axle has to be pulled and seal replaced.

Mar 01, 2011 | Chevrolet G20 Cars & Trucks

2 Answers

I have greese all over the rear brakes


Rear Axle seals are bad, they must be replaced. Good Luck

Jan 14, 2011 | 1993 Ford Econoline

1 Answer

Need to change rear seals in axcles how to? 98 gmc jimmy


First i would check to see if the axle air vent was clear if its not the oil is vary heavy and expands a lot this will build up pressure inside the houseing and cause the axle seals to leak if you can clear it the problem may fix it self its 80 90 weight oil thats thick stuff. If not you need to remove the rear wheels and brake drums then you have to remove the cover from the rear carriar catch the oil. Look inside the carriar houseing you will see the ends of the axles theres a small clip on each axle called a c clip remove them you can pull them out with your fingers. Then you can slide the axles out past the brake plates pry the seals out you might as well replace the bearings when your doing but thats up to you. Lube and install the bearings then the new seals you will need new seals lube the seal lips and vary carefuly slide the axle in taking care not to damage the seal install the c clip do the other side put a new gasket on the rear carriar tighten bolts to 20 ft lbs. Refill carriar 80 90 weight oil through filler plug on the side of the houseing until it just starts to run out hole put the plug in the rear drums on and wheels

Dec 30, 2010 | 1998 GMC Jimmy

1 Answer

How to get the rear wheel bearing out of 99 gmc jimmy


Dear Jimmy,
This repair is an intrusive repair if you have never done it.A chilton's manual can be purchased at your local auto parts store for $20 for your vehicle. Jack up the rear of vehicle and support it.Remove the rear tires.If the vehicle came with disc brakes remove the caliper and bridge, if not then remove the brake drum.Remove the rear diff cover, with a drain pan to catch the fluid.Remove your rear pinch thru bolt, your pin will then slide thru.Push both axles in to release and remove the u clips on the inside of the carrier assy, then pull both axles out.Remove the outer axle seal, throw away, ten using a bearing puller tool remove the bearing from the axle tube, install new bearing ad seal with drivers and reinstall axles.any other questions get back to me...I'm here to help!!!

Nov 21, 2009 | 2000 GMC Jimmy

1 Answer

How do I remove the rear axle to replace the seal 1996 jimmy


You will have to remove the differential cover on the rear end, in the center of the gear cluster you'll have to rotate your axle until it exposes the ends of the axle shafts, push in the axles as far as you can from the brake pad assembly area, then, there this a C clips that slips into a groove on the end of the axle, you'll have to reove the C clip to pull out the axle.

Apr 25, 2009 | 1996 GMC Jimmy

1 Answer

How to change the rear axleshaft oil seal


Jack it up, put it on stands. Remove the wheel, the brake drum, the differential cover, the axle clip, and pull your axle. Remove and replace the seal, install new diff gasket, re-install, and refill oil.

Feb 23, 2009 | 1998 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...