Question about 1997 Chevrolet Blazer

1 Answer

Remove the oil pan on a 1999 4x4 blazer do i have to remove the moter?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 836 Answers

Either the remove the motor or remove the front axel assembly. Either way is a long job. I advise you to secure a repair manual to help giude you along.

Posted on Apr 10, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change oil pan gasget


Jack up truck for safety sake put jack stands under frame . remove all engine oil remove all bolts holding oil pan on if their is not enough room to drop pan you may have to remove bolts holding motor mounts and jack up engine. if front end linkage is still in the way remove linkage. pull oil pan out. check gasket that was between block and oil pan if any stuck to block of engine remove with gasket scraper or wire brush or wire wheel on drill.make sure mating surface is clean put new gasket on new oil pan I like to use a high temp sealer on gasket both sides. Put pan with gasket back in place of old oil pan and tighten all bolts. jack engine down ,replace moter mount bolts replace any linkage you took apart. and dont forget to replace engine oil. make sure oil plug is in pan before pouring oil in . before starting engine check that no oil is leaking than start engine and check for any leaks again if all is good your done. if this was helpful please leave good feed back. A good temp fix on a rusted oil pan is JB weld make sure no oil is on pan clean with towel and rubbing alchol .you may have to drain oil first. if it is rusted badly you may have to use a wire brush on a drill to clean the area to patch. if patched properly it may last for years.

Oct 17, 2014 | 2000 GMC Sierra

1 Answer

How to change an oil pump on a s10 1991 chevy blazer


I would have to email you the instructions due to pics and length of instructions. It will be how to remove the oil pan and once the pan is off, 2 bolts to remove the pump and install the new one. The hardest part is getting to the pan usually. iambanshee74@yahoo.com

May 17, 2011 | 1991 Chevrolet S-10 Blazer

1 Answer

Oil pump where is it?


Hello.
The oil pump is mounted inside the oil pan and driven by a shaft that drives both the distributor and the oil pump.
The oil pan will need to be removed to access it.
Once the oil pan is off the oil pump is easy to change, although a messy job.
Thank you for using FixYa.

KL

Nov 26, 2010 | 1998 Chevrolet Blazer

2 Answers

1986 Chevy S-10 5 speed, where is my oil pump?


It's located to the rear part of the oil pan. To change it, the oil pan needs to be removed. To do this, the engine needs to be raised, or the transmission needs to be removed. Make sure it is the problem before just "changing" it.

Nov 12, 2010 | 1986 Chevrolet S-10 Blazer

1 Answer

Two questions: On A 2002 4x4 Blazer, is the oil drain plug on the oil pan? The only plug I see is under/behind the engine. Also does it turn counter clockwise to loosen, I was doing that and won't loosen.


Yes the oil drain plug is in the oil pan and the oil pan is on the motor.The plug is in the rear part of the oil pan and you need a 15mm wrench or socket to remove it.It does come off counter clockwise.Sometimes they are tightened to tight and can be hard to remove.Good luck.

Dec 07, 2009 | 2001 Chevrolet Blazer

1 Answer

Leaking oil really bad and need to know how to replace seal


drain the oil, remove the pan peel off old seal replace with new seal in pan and put the pan back on thighten down and refill to manufacturer seting for oil

Oct 29, 2009 | 1996 Chevrolet Blazer

3 Answers

We need to know how to get the oil pan out on a 1998 chevy 4-wheel drive blazer.


your going to have to remove motor mount bolts and jack motor up in order to get pan off. also after pan is hanging reach inside and unbolt oil pump and pick up screen to get enough roomto remove, hope this helps.

Oct 13, 2009 | 1998 Chevrolet Blazer

3 Answers

2000 Chevy Blazer


you have to remove motor mount bolts.... with engine hoist lift engine to get clearance to remove oil pan......you have to remove starter... trans cover ....... sounds like a easy job its not....hopethis helps

Dec 11, 2008 | 2000 Chevrolet Blazer

1 Answer

1999 Chevrolet Blazer oil pump


You must disconnect the motor mounts and remove the colling fan blade(so it won't hit the shroud) and raise the engine as high as poss, then remove the flywheel flex-plate cover and remove all the pan bolts, gently pry the pan from one side to the other until the gasket breaks loose, remove the old oil pump and reverse the procedure.

Oct 04, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...