Question about 1996 Pontiac Trans Sport

1 Answer

My tans sport 1996 wipers soped wprking fuse is good trying to find a relay pump for wiper wash stop working as well

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

Your symptoms are typically that of a defective fuse. There are no relays for either the wipers or the washer pump and both operate off the same fuse. Check the fuse again and make sure that it is making good contact on both contacts. With the ignition on, check that you have 12 v + on one of the fuse contacts to earth, use a volt meter or a 12 volt bulb to check this. If you have power and the wipers are still inoperative you will have to start looking at wiring and the wiper/washer switch incoming power wire right from the fuse box.

Posted on Apr 10, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

3 Answers

Its a 1997 montero sport


it could be the actual motor burnt out or siezed wich is causing the fuses to blow and the motor is under the bonet just below the windowscreen near the top vents.

Jul 25, 2008 | 2000 Mitsubishi Montero Sport

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

3 Answers

My f250 2003 wipers and pump dont work iv replaced switch and wiper moter fuses are good the 2 i could locate for wipers


Have you done a Probe Test on the vehicle? A Probe Light Tester can help you locate a short in your cars electrical system. To learn what a Probe Tester is and How to use it, watch the following video: https://www.youtube.com/watch?v=tXzKcEyIOq8

Dec 22, 2015 | Cars & Trucks

1 Answer

How do I find the wiper relay on my 1997 BMW 740il. I ordered a factory wiper relay .its Tan in color, I cant find it. I need help from a professional can you help me.


It's located inside the power distribution panel.

The power distribution panel on your car is located under the hood in the engine compartment. It is located on the right passenger side closest to the firewall.

When you open the cover to the PDP, you'll see a series of blade type fuses in the front compartment and a bunch of wire harnesses in the back- that's where you'll find the tan colored relay you need to replace.

I have attached a youtube video for you to watch because it appears that the most common cause of this relay failure is due to water build up in the PDP compartment which is causing serious wiring deterioration and rusting- not only to the wiper relay but to the other relay components in that block.

So should you be experiencing the same problem when you open the power distribution panel, you'll know what to do.

http://youtu.be/PoX3w-D-kG0

Feb 28, 2015 | 1997 BMW 740il

1 Answer

Could a silver square relay looking fuse thingy broken off stop my wipers from working?


I replaced my relay as my wipers stopped working after replacing the relay my wipers work again was going to get a new wiper motor but glad I tried the relay first so much easier

Apr 17, 2009 | 1996 Jeep Cherokee

1 Answer

Windshield wipers on pt cruiser


the pump wire is probably not making good connection with the pump that is why the washer fluid wont work try and clean the connection. the pump is located under the fill tank

check for a bad relay for the wipers not working. the relay will be under the hood or under the dash next to the fuses. the cover will tell you what piece is the relay. the relay controls the delay in the wipers so that is probably bad and you can get them at napa for cheap. and simple to install its just like a fuse.

Mar 28, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Windshield wipers


From your owners manual:

Fuse#11 30A , Wiper Run/Park
Relay, Wiper Hi/LO Relay, Windshield Wiper
Motor, Rear Washer Pump Relay

U will also need to check the relays if the fuse is ok, the relay, it is the underhood fuse box
Relay #202 — Front Wiper Run/Park Relay

Dec 18, 2008 | 2001 Lincoln Navigator

1 Answer

Front wipers on my 1996 Pontiac Trans Sport stop mid-cycle


A couple things could be but not limited to - weak motor, wiper transmission needs lubricant, worn out bushings or bearings for wiper arm causing added friction. You might take to a GM Dealer to see if there is a bulletin or notice about the wipers. 

Jun 12, 2008 | 1996 Pontiac Trans Sport

Not finding what you are looking for?
1996 Pontiac Trans Sport Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...