Question about 2001 Ford F150 Styleside SuperCrew

1 Answer

Will not shift into gear from park with motor running, also cab lights and electric windows not working. Will start from neutral and then shift into gears.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 984 Answers

Might want to start with checking your stop lamps & the fuse for the stop lamps.

The shift interlock is part of the stop lamp circuit on the 97-03 MY trucks, and without working stop lamps, the truck does not come out of park,

Not too sure what you mean by cab lights, is this the interior dome lamps or the instrumentation illumination ?

Posted on Apr 12, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car won't start lights and radio work just had catalytic convertor replaced 2 days ago


First explain why it won't go into neutral. This may be the problem for no start.

Jul 29, 2016 | 2007 Suzuki SX4 AWD

1 Answer

I have a 1990 F250 xtra cab with a 460 cui, 7.5 liter fuel injected gas guzzler, The steering wheel must be tilted all of the way up for it to start, and sometimes i need to wiggle the gear selector, it is...


You should either check the neutral switch on the column inside by the base or the steering wheel or replace it. Sounds like it maybe shorting out or a wire is pinching.

Jun 23, 2017 | 1990 Ford F250

1 Answer

I HAVE A 1990 LS 400 WHEN TURNING KEY NO CRANKING AND HAVE GOOD BATTERY POWER. NO POWER TO STARTER WIRE ON STARTER SELINOD.WHAT CAN IT BE


It could be a bad ignition switch or bad starter wire from the starter switch, or the PNP is not adjusted correctly:

Here are instructions on how to remove and replace the PNP, but read over it to understand how to adjust:
Park/Neutral Safety Switch REMOVAL AND INSTALLATION ES300 1993-94 Models
  1. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  2. Raise and safely support the vehicle.
  3. Disconnect the Park/Neutral switch connector.
  4. Remove the clip from the shift control cable.
  5. Remove the nut and control cable.
  6. Remove the bolts and pull out the Park/Neutral switch. To install:
  7. Install the Park/Neutral switch and loosely install the bolts.
  8. Adjust the switch and torque the bolts to 48 inch lbs. (5 Nm).
  9. Install the control shaft lever.
  10. Install the control shaft cable and torque the nut to 9 ft. lbs. (13 Nm). Fig. 1: The transaxle control shaft lever has a nut and washer to retain it - 1993-94 ES300 54617.gif
    Fig. 2: Removing the Park/Neutral switch - 1993-94 ES300 54618.gif

  11. Install the clip to the shift control cable.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Make sure the vehicle will start only in the PARK or NEUTRAL position.
1995-97 Models Fig. 3: Aligning the neutral base line and groove - 1995-97 ES300 293716.gif
Fig. 4: Park/Neutral switch removal and installation - GS300, LS400, SC300 and SC400 300569.gif
Fig. 5: Park/Neutral switch adjustment - GS300, LS400, SC300 and SC400 300571.gif
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Apply the parking brake fully and block the rear wheels.
  3. Disconnect the electrical connector from the Park/Neutral position switch.
  4. Remove the locknut and disconnect the control cable from the manual shift lever.
  5. Remove the clip from the holding the control cable to the bracket.
  6. Remove the nut, washer and the manual shift lever from the manual valve shaft.
  7. Using a flat bladed tool, bend the lock washer back away from the nut.
  8. Remove the nut and lock washer from the Park/Neutral switch.
  9. Remove the two bolts and the Park/Neutral position switch. To install:
  10. Install the Park/Neutral position switch to the manual valve shaft. Leave the two bolts loose at this time.
  11. Install the lock washer and nut. Torque the nut to 61 inch lbs. (7 Nm).
  12. Using a flat bladed tool, bend the lock washer over the nut to secure the nut in place.
  13. Adjust the Park/Neutral as follows:
    1. Install the manual shift lever to the Park/Neutral switch and set the shift lever to the neutral ( N) position.
    2. Align the groove and the neutral basic line on the Park/Neutral switch.
    3. Hold the Park/Neutral switch in this position and tighten the two bolts to 48 inch lbs. (5 Nm).
  14. Install the manual shift lever with washer and nut.
  15. Install the control cable to the manual shift lever and install the nut. Torque the nut to 11 ft. lbs. (15 Nm).
  16. Install the control cable to the bracket by installing the clip.
  17. Connect the electrical connector to the Park/Neutral switch.
  18. Lower the vehicle and check the vehicles shifting positions.
  19. Connect the negative battery cable to the battery.
  20. Verify that the vehicle only starts in PARK or NEUTRAL.
GS300, LS400, SC300 and SC400
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Raise and safely support the vehicle.
  3. If necessary, remove the front exhaust pipe.
  4. Disconnect the neutral start switch connector.
  5. Remove the control shaft shift lever.
  6. Pry off the washer and remove the nut.
  7. Remove the bolt and pull out the neutral start switch. To install:
  8. Install the Park/Neutral switch and loosely install the bolt.
  9. Adjust the switch as follows:
    1. Loosen the neutral start switch bolt and place the shift lever in the N position.
    2. Align the groove and the neutral basic line.
    3. Hold in position and tighten the bolt to 9 ft. lbs. (13 Nm).
  10. Install the nut and washer.
  11. Install the control shaft shift lever.
  12. Connect the electrical connector.
  13. Install the front exhaust pipe. Torque the front nuts to 46 ft. lbs. (62 Nm). Torque the pipe support bracket to bolts to 32 ft. lbs. (43 Nm). Torque the No. 2 front exhaust pipe to the front exhaust pipe bolts to 32 ft. lbs. (43 Nm).
  14. Lower the vehicle.
  15. Connect the negative battery cable to the battery.
  16. Verify that the vehicle will only start in the N or P positions.
---
Maybe try to press the brake pedal and run the gear shift throughout the full range of gears while the car is on level ground, and retry the starter to see if there is a faulty PNP adjustment.

Try to start in Neutral not Park, and jiggle the gear shift back and forth to see if the PNP is not adjusted right.

Good luck on this repair.

Nov 09, 2010 | 1992 Lexus Ls 400

1 Answer

I cannot shift my 98 Sable out of park into a gear after it starts, if I turn the engine off then turn the key to on (not engaging the starter) the gear shift can be moved to neutral then the engine starts...


Sounds like a problem with the brake light switch. Do the brake lights work? It is a problem with the shift interlock system. It is controlled by the brake light switch on the brake pedal bracket.

Aug 02, 2010 | 1998 Mercury Sable

1 Answer

Gear shift of f-150 is locked in park. The truck


Is the CHMSL ( Center High Mount Stop Lamp ) working ?
Is it a regular bulb, or did it get changed to a LED ?
If it is a functioning factory type bulb, the shift interlock solenoid is the cause.
Until you can fix the CHMSL or the shift interlock, you can turn the key to the run position ( do not start ), press and hold the brake pedal, shift into neutral, and then start the truck.
Your MY the shift interlock circuit and the brake lamp circuit are the same.
Usually the shift interlock stops working when the brake lamp fuse is blown, or if the bulbs are out ( truck does not see a load on the circuit ).
If LED tail lamps were installed without load resistors, the shift interlock circuit will not work ( looks like a burnt out brake lamp bulb )

Jan 11, 2010 | 1997 Ford F150 Regular Cab

2 Answers

Trouble Starting 1994 Dodge Dakota


SOUNDS LIKE IT IS ACTUALLY THE NEUTRAL SAFETY SWITCH ON THE TRANSMISSION!!

Jun 30, 2009 | 1994 Dodge Dakota Club Cab

2 Answers

All my guages went out at the same time...windows


sounds like alot of problems, have rolled into 1, without looking at it with my eyes, could be the main electric box that has just packed in

Jun 05, 2009 | 1997 Honda Accord

2 Answers

My 2003 Mercury Mountaineer Gear Shift is stuck.


THERE IS A SENSOR ON THE BRAKE PEDAL THAT RELEASES THE THE SHIFTER.THERE A 3 COMPONENTS INVOLVED.U CAN PUT IT IN NEUTRAL BEFORE U START THE CAR.THEN WIL SHIFT.

May 01, 2009 | 2004 Mercury Mountaineer

1 Answer

2007 dodge caravan, won't start at first. I leave it and fiddle with the gear shift and finally it starts. Runs no problem, shut it off and it restarts. Noticed that the gear shift light shows reverse when...


Sounds like the shifter linkage needs adjusted. There is a neutral saftey switch that prevents the car from being started in any foward or reverse gear. If the shifter linkage is out of adjustment, the neutral safety switch will give you starting problems.

Apr 11, 2009 | 2007 Dodge Grand Caravan SXT Minivan

Not finding what you are looking for?
2001 Ford F150 Styleside SuperCrew Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...