Question about Mazda B2600

Open Question

Left hand rear axle b2600 4x4 bravo 1996 - B2600 Mazda Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: can not remove rear axle on chevy avalanche 4x4 1500.

you will need to take off the differential cover (drain and change diff oil at this time)

rotate the axle so that you can get at the cross pin and remove it by undoing a small bolt that holds it in place. it should slide out with ease, but i have had them stick, take care not to let the cross pin get lodged where it is difficult to extract

a single C-clip is holding each axle inside the differential housing

you will need to push in from the outer end of the axle, while simultaneously manipulating the C-clip off of the inner axle, repeat this same process on the other side

i will put some of pics up in a minute

Posted on Feb 09, 2009

Ad
heavymetal77
  • 721 Answers

SOURCE: rear axle leaking

Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

Posted on Jun 23, 2009

cshubart
  • 146 Answers

SOURCE: how do you a Replace rear axle seal

first drain fluid and remove diff cover take off tires theres a c-clip in the diff that needs to be removed so you can take the axles out the seal is behind the axles pull old ones and install new replace c-clip and cover fill with recomender diff oil you should be good

Posted on Oct 07, 2009

  • 881 Answers

SOURCE: Have Mazda bravo B2600 4WD ,has white smoke &

You dont say weather its a petrol or diesel engine as there a slight differance in the answer and if a turbo on a diesel thats even more of a differance, but taking it a petrol .
Well to start with the white smoke Isent smoke its water and after going through the engine it turns into Steam and thats what you see..
Running on 3 clyinders is caused through 1 cylinder isent working as a engine should and has a bad valve or a broken piston ring or more and even a cracked head and gasket letting the water through,,,also the broken ring works like a oil pump as if not firing given you power then it works like a oil pump and pumps it into the cylinder that dosent work only pumping oil into the hot exhaust system while running.CAUSING SMOKE
And if a turbo then could be the turbo bearings worn and pushing oil into the engine and still doing the same as before.
Let me know how you get on. RON

Posted on Nov 17, 2009

roniecon
  • 6826 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu rodeo front axle acutator has power going to both switches


got this.?>
The 1996 Trooper and Rodeo models were available with a shift-on-the-fly system,

SOF
which incorporates an assembly mounted on the left-hand side of the front axle unit.
the shift-on-the-fly unit includes a housing, an actuator assembly and various Vacuum Switching Valves (VSV).
here it is, SOF.
if the right switch is 12vdc on both pins
then the relay closes, does it?
if it closed the 2 VSV both go HOT,12v. brown-blk wire.
do they?
the left switch below is only for the silly dash light.
then there is the vacuum side.... more details....

25835889-b0qotdfot4r50rcgu1whx1iy-5-0.jpg

Aug 24, 2015 | 1996 Isuzu Rodeo

1 Answer

How do I remove the rear axle nut on a 2001 mazda MPV?


No, it would not be left hand threads. Just on super tight, probabvly torqued down to about 200 ft. lbs. Use a good stout breaker bar.

Aug 23, 2012 | 2001 Mazda MPV

1 Answer

How do you a Replace rear axle seal on a 2WD 1996 Silverado. I have an oil leak dripping onto the iside of me left rear tire.


first drain fluid and remove diff cover take off tires theres a c-clip in the diff that needs to be removed so you can take the axles out the seal is behind the axles pull old ones and install new replace c-clip and cover fill with recomender diff oil you should be good

Oct 07, 2009 | Chevrolet Silverado Cars & Trucks

1 Answer

Rear axle bearing lock washer and nut coming loose


You may have incorrect axle end play. The left axle is fitted with a 1mm shim and an o-ring between the bearing housing and diff flange. The right bearing housing should be shimmed to suit specs. If the right axle has too much end play, it may try to walk.

Aug 16, 2009 | 1988 Mitsubishi Pickup

1 Answer

Unable to pull out rear axle to change brearing


remove differential cover,turn axle until chunk turns around to access the small 5/16pin bolt remove pin bolt ,slide spider gear axle rod out ,go to axle ur working on and push axle inward ,ther is a c shaped key on end of axle where u took spider axle rod out remove this key easly by hand and pull axle out,,,note do not turn chunk after removing spider axle rod or ur spiders will fall out

Jun 28, 2009 | 1996 Chevrolet Blazer

1 Answer

How do I remove the rear axle to replace the seal 1996 jimmy


You will have to remove the differential cover on the rear end, in the center of the gear cluster you'll have to rotate your axle until it exposes the ends of the axle shafts, push in the axles as far as you can from the brake pad assembly area, then, there this a C clips that slips into a groove on the end of the axle, you'll have to reove the C clip to pull out the axle.

Apr 25, 2009 | 1996 GMC Jimmy

1 Answer

Spider gears fell on rear differential 95 ford explorer


It's not easy to put them back, but if you get the side gears in position with the axles bumped out as far as you can, the smaller spider gears can be "walked" into place. Try having your buddy rotate one of the wheels slowly until each one fits in. It's tricky but you'll get it.

Apr 04, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...