Question about 1993 Ford Bronco

1 Answer

Need help with window seals on the drivers door.

Took out the old seals and am trying to get the new seals in but i am having difficulties or well in truth i cant get it to work.

so is there an easy way to do it that i am missing or what?


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

The two pieces at the bottom of the window attach seperately to the sheet metal. There is an inside and an outside piece. They grip the sheet metal with clips. You will need to press them on or tap lightly to install. They can be difficult to install. Make sure the clips line up with the slot and press into place. The same goes with the seal around the window. It pushes in to the gap.

Posted on Mar 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

98 olds passanger window off track

remove door handles, then door panel (carefully), disconnect wiring carefully as you remove door panel, remove seal covered metal of door, investigate why window glass is not in track. May have get new track seal and track -- usually corrosion a the cause

Feb 05, 2015 | Cars & Trucks

1 Answer

Can not get new trans filter to slide into the hole in the valve body. seams like the new rubber seal is to big.. took out the old seal..what can i do. 03 ford windstar lx

Insure that you have the correct part and use wooden dowel just larger than seal if needed to drive it into place. This should not require much effort if you have the correct part.

Jan 21, 2015 | Ford Cars & Trucks

1 Answer

How to remove a transaxel rubber seal from a 1998 dodge avenger

just pier it out with a screw driver it is no good so it does not matter how it comes out,but the new one needs to be installed carefully

Dec 03, 2012 | 1998 Dodge Avenger

1 Answer

How do i repair an exterior window seal on the side door

Pull old seal out
New seal should just slot in with abit of effort and help from a flat head screw driver you should be able to prize it into place

Jun 21, 2010 | 2006 Chrysler Pacifica

2 Answers

I took the radiator cap off and it looked like brown mud in there, supposed to be " red " dexcool.... am i screwed or not.. 44000 miles, bought from a little old lady (seriously) rest of car is cherry.......

Hello. To install cruise from a wreck is not possible for the home mechanic. Thre are kits available at most Auto Parts houses. The rust in your radiator is caused by someone using water instead of proper coolant. Buy a flushing kit at your local parts store and use it, following the instructions. You'll not have any more difficulties IF you keep a proper engine coolant in it.

Apr 26, 2010 | 1998 Buick Century

1 Answer

Driver side window isnt working but the rest

I believe you need a new switch in drivers door goto a wrecker , new GM ones are $$$$$, happened to me, i just unhooked battery to clear a CEL and had window open at the time ( won't do that again ) and door locks and drivers window won't work ,, checked fuses ,everything good then took door apart and put power to window motor was able to put it up, googled and found lots of people in same boat , hope it works for you ,,,,D

Nov 27, 2009 | 2005 Chevrolet Colorado

1 Answer

Driver side window will not go down.. all other windows work

Check for broken wires in the pass through from the door to frt pillar. These cars have problems with broken wires all the time.

Jun 30, 2009 | 1995 Oldsmobile Aurora

1 Answer

Removing/installing door components from/to door shell

sorry i cant tell u how to exactly howto take the old door apart NICELY without just having a light touch and the experience of doing other doors, but i would like to ask where u got ur door shell, i need one badly myself to and have had no luck so far finding one. any knowlage u have would be awsome, thanks

Mar 24, 2009 | 2003 Toyota Corolla

1 Answer

Side door glass removal

ok first thing first if you can spend roughly 80.00 I would call a mobile glass company or look for a van that does glass. They will do it and they can take the old one out and replace it within an hour/ the reason I say this is they need a chemical to bit into the your door and urethane it in now think of this 80.00 for glass guy or 10.00 for the chemical for bite one tube of caulk 30.00 plus your time and its pretty valuable and the professional put in hands down is the thing.You will appreciate this that i am teeling you.Hopefully you thought of that.I know you can do it just the but thing. if you need any more info go to ok jmdf

Mar 09, 2009 | 2002 Chevrolet Astro

2 Answers

There is a water leak somewhere in my 98 toyota camry that leaks into my passenger side floor. There is no sun roof and no visible leaks from the windows or doors. Any thoughts? A/C leak maybe? water...

I am the original owner of camry xle 1998 with wet floors. In 2000 I had drivers side door seal leaking at welt. Removed old door seal and new weather strip on drivers side installed. The door panel was never wet, but wet at bottom of door where there are drain holes...slowly leaking under carpet.
In 2001 later water again. Coming from overflowing A/C evaporator-drain plugged/ tank full of debris. Removed evaporator, cleaned + drain cleaned.
In 2003, driver door seal against window rotted. Removed door panel and found leak at window belt molding at the mirror joint inside + out. Lots of mold under carpet needed to replace! Made a fuss at dealers for reacurring problem and they replaced the carpet for free.

Sep 07, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
1993 Ford Bronco Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides