Question about Suzuki Sidekick

1 Answer

When left signal is applied there is a loud buzzing sound briefly then it stops

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The turning signal rely is problely going bad replace rely

Posted on Apr 09, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Why is my 2008 chevrolet uplander's turn signal does not making clicking sound , but the signal lights are working.


Did you put a aftermarket radio in ? The clicking sound comes out the driver side speaker . It's generated by the BCM body control module .
Turn Signal Lamps
The STOP/TURN fuse in the instrument panel (I/P) fuse block supplies battery positive voltage to the body control module (BCM) for the turn signal lamps. When the turn switch is placed in the left or right position, ground is applied to the BCM on the left or right turn signal switch signal circuit. The BCM then applies voltage to the appropriate front and rear supply voltage circuits.
Grounds for the various lamps are as follows:
• G100 supplies the right front lamps
• G101 supplies the left front lamps
• G400 supplies the right rear lamps
• G401 supplies the left rear lamps

Your best bet would be to take it to a qualified repair shop before you start replacing parts , like the BCM ,which would need to be programmed at the dealer or other thing's will stop working too .

Aug 30, 2017 | Chevrolet Cars & Trucks

1 Answer

Intermittent buzzing sound at turn signal switch - 97 suburban


You found it. and you verified it the solution and the fix is the turn signal switch

Mar 17, 2012 | 1997 Chevrolet Suburban

1 Answer

Issues with turn signal in my 2001 Oldsmobile Alero. Hazard lights and right/left turn signal emit a very loud buzzing, then gets stuck. It does not work most of the time, or when it does, it buzzes...


Sounds like you have a bad multi-function switch or signal switch they are the same thing.This will fix the cruise control but,your other problem is your hazard warning switch replace it to.This will fix both of your problems.P.S you can get both of these from www.rockauto.com for less than $60.00.

Apr 20, 2011 | 2001 Oldsmobile Alero

1 Answer

Hello, When i apply my signal left or right ,It will make a buzzing sound, If i turn it off and then re apply it its fine. I chanded the relay under the knee plate but it still made the same sound and the...


I just fixed the same problem, the turn signal switch has a bad connection inside of it. i took mine apart and did some soldering and fixed it. if you try this be careful things and springs tend to fly out.
I believe your switch runs about $55.00. And they are not hard to replace. remove the column coverscrews on the bottom. Two screws and two plugs and teh switch is replaced.
Good luck
Randy

Nov 10, 2010 | 1997 Ford Explorer AWD

2 Answers

97 honda accord turn signal problem


Flasher unit is bad. Replace flasher

Dec 28, 2008 | 1997 Honda Accord

1 Answer

1994 Honda Passport


I just today had this problem fixed at a shop. The entire assembly has to be replaced that has the turn signal arm and the cruise control arm. The part was $186.00 and the labor was $90.00
Kevin

Oct 27, 2008 | 1994 Honda Passport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...