Question about 1988 Nissan Sentra 2 Door

Open Question

No power to the air conditioner switch inside the car. Engine condenser fan won't turn on. All the fuses are intact. The systems pressure is at perfect levels. Before This happened I was working inside the car. Working on the dashboard. Not 100% sure using the right wire for the switch, but there are no other wires that fit it. Something is disconnected somewhere or there is a short. Last. I was also working on the cooling system and antifreeze spilled on the condenser and fan area. The inside switch does not light up at all.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1988 nissan sentra air conditioner. Electical problem

My 1988 Nissan AC quit working soon after having the compressor & ect replaced. AC Tecnition took the switch box out from under the dash and cleaned it. He also fixed a loose wire in it. He said this cars switch box calcimates and does not make good contact. AC works great.

Posted on May 09, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Condenser fan not engaging


Possibly low on refrigerant. When system is low on freon, it does not build up enough high side pressure to engage the condenser fan . When pressure is high enough. a high side pressure switch kicks on the cond. fan to maintain high side pressure. Have the system evacuated and recharged to proper level.

Feb 01, 2014 | 1996 Mercedes-Benz C-Class

1 Answer

Where is the air conditioner blower fan relay on 1996 Jeep Grand Cherokee located?


The blower fan relay is located in the fuse box on the driver's side fender-well. A Jeep Cherokee uses an electric fan as an auxiliary fan for engine cooling and for cooling the air conditioning condenser when the air conditioning is in operation. A radiator temperature-sensing switch that activates the fan relay at 198 degrees F turns the fan on and controls its operation. The temperature drops when the vehicle is in motion and the switch turns the fan off. When the air conditioning system is in operation, the air conditioning relay supplies power to the fan relay via a fan diode downstream from the ignition switch. This diode activates the fan relay and keeps the fan operating as long as the air conditioning is on. Thanks. you can rate this solution and show your appreciation.

May 18, 2010 | Cars & Trucks

1 Answer

The air conditioner doesn't work


HI. Here is a complete check list that will help you trouble shot thsi issue. You will find the problem in one or more of these areas stated below.

1. Check Drive Belts - The air conditioner utilizes a drive belt that supplies power to rotate the compressor, which is basically a refrigerant pump. If the belt fails the compressor has nothing to drive it, inspect and replace as needed to restore operation. If belt is intact proceed to the next step.

2. Check for Compressor Clutch Engagement - Turn the air conditioner to the "on" position and set controls to the coldest setting. Start the engine and allow to idle. Then open the hood and inspect the clutch at the front of the compressor, is it turning? "Engaged" if so, the system has enough refrigerant to activate. If the system is low on refrigerant it will not work properly. In this case an air conditioner recharge kit is needed to recharge the system. If the system is low on refrigerant it could cycle on and off, making a ticking noise. If the compressor clutch is not turning proceed to next step.

3. Inspect for Refrigerant Leaks - If the system has a large leak and no refrigerant remains it will not activate. First test system for a static pressure charge, with the engine off attach an ac gauge to the low side pressure port and check the state of charge. Depending on outside temperature there should be between 50 psi and 80 psi. (Cool and warm). A refrigerant leak detector is needed to inspect for leak, but if you do not have a leak detector there is an alternative method. The air conditioner system is designed to run with oil suspended in the refrigerant to lubricate the system. Check for oily residue outside the system by inspecting all hoses, compressor, condenser, evaporator or receiver drier and replace any component that has failed.

4. Inspect Fuses - Check under dash panel and under hood power distribution center. Replace failed fuses as needed, recheck system. If the new fuse fails when reinstalled a short circuit is present and requires diagnosing with a wiring schematic, follow circuits to locate short, repair as needed and recheck system.

5. Check Temperature Control Vents - The vents inside your car are controlled by a cable, electrical servo or vacuum servo. If the temperature blend door is not functioning properly it will cause warm air from the heater to exit the vents. To check this start the car and allow the engine idle, next turn the blower motor speed on low, switch the temperature control from warm to cold while your ear is close to the vents. You should hear the door move inside the heater box as it swings from open to close. If not, insect for a vacuum leak or a shorted motor in the servo, repair the leak or replace the servo motor.

Oct 02, 2009 | 1992 Honda Accord

1 Answer

A/c deosnt blow cold on hot days,fre-ion level is good ,and condenser is cold


HI. Here is a complete check list that will help you trouble shot this issue. You will find the problem in one or more of these areas stated below.

1. Check Drive Belts - The air conditioner utilizes a drive belt that supplies power to rotate the compressor, which is basically a refrigerant pump. If the belt fails the compressor has nothing to drive it, inspect and replace as needed to restore operation. If belt is intact proceed to the next step.

2. Check for Compressor Clutch Engagement - Turn the air conditioner to the "on" position and set controls to the coldest setting. Start the engine and allow to idle. Then open the hood and inspect the clutch at the front of the compressor, is it turning? "Engaged" if so, the system has enough refrigerant to activate. If the system is low on refrigerant it will not work properly. In this case an air conditioner recharge kit is needed to recharge the system. If the system is low on refrigerant it could cycle on and off, making a ticking noise. If the compressor clutch is not turning proceed to next step.

3. Inspect for Refrigerant Leaks - If the system has a large leak and no refrigerant remains it will not activate. First test system for a static pressure charge, with the engine off attach an ac gauge to the low side pressure port and check the state of charge. Depending on outside temperature there should be between 50 psi and 80 psi. (Cool and warm). A refrigerant leak detector is needed to inspect for leak, but if you do not have a leak detector there is an alternative method. The air conditioner system is designed to run with oil suspended in the refrigerant to lubricate the system. Check for oily residue outside the system by inspecting all hoses, compressor, condenser, evaporator or receiver drier and replace any component that has failed.

4. Inspect Fuses - Check under dash panel and under hood power distribution center. Replace failed fuses as needed, recheck system. If the new fuse fails when reinstalled a short circuit is present and requires diagnosing with a wiring schematic, follow circuits to locate short, repair as needed and recheck system.

5. Check Temperature Control Vents - The vents inside your car are controlled by a cable, electrical servo or vacuum servo. If the temperature blend door is not functioning properly it will cause warm air from the heater to exit the vents. To check this start the car and allow the engine idle, next turn the blower motor speed on low, switch the temperature control from warm to cold while your ear is close to the vents. You should hear the door move inside the heater box as it swings from open to close. If not, insect for a vacuum leak or a shorted motor in the servo, repair the leak or replace the servo motor.

Aug 29, 2009 | 1993 Ford Probe

1 Answer

Air conditioner not working. Coolant seems to be full.


Check the following areas in order to address this issue.

1. Check Drive Belts - The air conditioner utilizes a drive belt that supplies power to rotate the compressor, which is basically a refrigerant pump. If the belt fails the compressor has nothing to drive it, inspect and replace as needed to restore operation. If belt is intact proceed to the next step.

2. Check for Compressor Clutch Engagement - Turn the air conditioner to the "on" position and set controls to the coldest setting. Start the engine and allow to idle. Then open the hood and inspect the clutch at the front of the compressor, is it turning? "Engaged" if so, the system has enough refrigerant to activate. If the system is low on refrigerant it will not work properly. In this case an air conditioner recharge kit is needed to recharge the system. If the system is low on refrigerant it could cycle on and off, making a ticking noise. If the compressor clutch is not turning proceed to next step.

3. Inspect for Refrigerant Leaks - If the system has a large leak and no refrigerant remains it will not activate. First test system for a static pressure charge, with the engine off attach an ac gauge to the low side pressure port and check the state of charge. Depending on outside temperature there should be between 50 psi and 80 psi. (Cool and warm). A refrigerant leak detector is needed to inspect for leak, but if you do not have a leak detector there is an alternative method. The air conditioner system is designed to run with oil suspended in the refrigerant to lubricate the system. Check for oily residue outside the system by inspecting all hoses, compressor, condenser, evaporator or receiver drier and replace any component that has failed.

4. Inspect Fuses - Check under dash panel and under hood power distribution center. Replace failed fuses as needed, recheck system. If the new fuse fails when reinstalled a short circuit is present and requires diagnosing with a wiring schematic, follow circuits to locate short, repair as needed and recheck system.

5. Check Temperature Control Vents - The vents inside your car are controlled by a cable, electrical servo or vacuum servo. If the temperature blend door is not functioning properly it will cause warm air from the heater to exit the vents. To check this start the car and allow the engine idle, next turn the blower motor speed on low, switch the temperature control from warm to cold while your ear is close to the vents. You should hear the door move inside the heater box as it swings from open to close. If not, insect for a vacuum leak or a shorted motor in the servo, repair the leak or replace the servo motor.

Aug 13, 2009 | 2006 Dodge Ram 3500 Truck

1 Answer

Air conditioning systems don't work


HI. I have put together some very important check points that you should use to isolate the issue that concerns this inoperable AC system.

1. Check Drive Belts - The air conditioner utilizes a drive belt that supplies power to rotate the compressor, which is basically a refrigerant pump. If the belt fails the compressor has nothing to drive it, inspect and replace as needed to restore operation. If belt is intact proceed to the next step.

2. Check for Compressor Clutch Engagement - Turn the air conditioner to the "on" position and set controls to the coldest setting. Start the engine and allow to idle. Then open the hood and inspect the clutch at the front of the compressor, is it turning? "Engaged" if so, the system has enough refrigerant to activate. If the system is low on refrigerant it will not work properly. In this case an air conditioner recharge kit is needed to recharge the system. If the system is low on refrigerant it could cycle on and off, making a ticking noise. If the compressor clutch is not turning proceed to next step.

3. Inspect for Refrigerant Leaks - If the system has a large leak and no refrigerant remains it will not activate. First test system for a static pressure charge, with the engine off attach an ac gauge to the low side pressure port and check the state of charge. Depending on outside temperature there should be between 50 psi and 80 psi. (Cool and warm). A refrigerant leak detector is needed to inspect for leak, but if you do not have a leak detector there is an alternative method. The air conditioner system is designed to run with oil suspended in the refrigerant to lubricate the system. Check for oily residue outside the system by inspecting all hoses, compressor, condenser, evaporator or receiver drier and replace any component that has failed.

4. Inspect Fuses - Check under dash panel and under hood power distribution center. Replace failed fuses as needed, recheck system. If the new fuse fails when reinstalled a short circuit is present and requires diagnosing with a wiring schematic, follow circuits to locate short, repair as needed and recheck system.

5. Check Temperature Control Vents - The vents inside your car are controlled by a cable, electrical servo or vacuum servo. If the temperature blend door is not functioning properly it will cause warm air from the heater to exit the vents. To check this start the car and allow the engine idle, next turn the blower motor speed on low, switch the temperature control from warm to cold while your ear is close to the vents. You should hear the door move inside the heater box as it swings from open to close. If not, insect for a vacuum leak or a shorted motor in the servo, repair the leak or replace the servo motor.


Jul 28, 2009 | 1995 Audi 90

2 Answers

Ac compressor not working


Low pressure or Freon or bad sensor for it will not allow a compressor to engage. It is a safety feature to save it.

Jun 11, 2009 | 1992 Nissan Pickup

1 Answer

Ac controle blows out hot air, seems heater is on all the time


HI. Here is a complete check list that will help you trouble shot this issue. You will find the problem in one or more of these areas stated below.

1. Check Drive Belts - The air conditioner utilizes a drive belt that supplies power to rotate the compressor, which is basically a refrigerant pump. If the belt fails the compressor has nothing to drive it, inspect and replace as needed to restore operation. If belt is intact proceed to the next step.

2. Check for Compressor Clutch Engagement - Turn the air conditioner to the "on" position and set controls to the coldest setting. Start the engine and allow to idle. Then open the hood and inspect the clutch at the front of the compressor, is it turning? "Engaged" if so, the system has enough refrigerant to activate. If the system is low on refrigerant it will not work properly. In this case an air conditioner recharge kit is needed to recharge the system. If the system is low on refrigerant it could cycle on and off, making a ticking noise. If the compressor clutch is not turning proceed to next step.

3. Inspect for Refrigerant Leaks - If the system has a large leak and no refrigerant remains it will not activate. First test system for a static pressure charge, with the engine off attach an ac gauge to the low side pressure port and check the state of charge. Depending on outside temperature there should be between 50 psi and 80 psi. (Cool and warm). A refrigerant leak detector is needed to inspect for leak, but if you do not have a leak detector there is an alternative method. The air conditioner system is designed to run with oil suspended in the refrigerant to lubricate the system. Check for oily residue outside the system by inspecting all hoses, compressor, condenser, evaporator or receiver drier and replace any component that has failed.

4. Inspect Fuses - Check under dash panel and under hood power distribution center. Replace failed fuses as needed, recheck system. If the new fuse fails when reinstalled a short circuit is present and requires diagnosing with a wiring schematic, follow circuits to locate short, repair as needed and recheck system.

5. Check Temperature Control Vents - The vents inside your car are controlled by a cable, electrical servo or vacuum servo. If the temperature blend door is not functioning properly it will cause warm air from the heater to exit the vents. To check this start the car and allow the engine idle, next turn the blower motor speed on low, switch the temperature control from warm to cold while your ear is close to the vents. You should hear the door move inside the heater box as it swings from open to close. If not, insect for a vacuum leak or a shorted motor in the servo, repair the leak or replace the servo motor.

Apr 08, 2009 | 2001 Ford Expedition

1 Answer

1988 nissan sentra air conditioner. Electical problem


My 1988 Nissan AC quit working soon after having the compressor & ect replaced. AC Tecnition took the switch box out from under the dash and cleaned it. He also fixed a loose wire in it. He said this cars switch box calcimates and does not make good contact. AC works great.

Jan 18, 2009 | 1988 Nissan Sentra 2 Door

1 Answer

When starting the car the AC Compressor wont come on right away


HI. Here is a complete check list that will help you trouble shot thsi issue. You will find the problem in one or more of these areas stated below.

1. Check Drive Belts - The air conditioner utilizes a drive belt that supplies power to rotate the compressor, which is basically a refrigerant pump. If the belt fails the compressor has nothing to drive it, inspect and replace as needed to restore operation. If belt is intact proceed to the next step.

2. Check for Compressor Clutch Engagement - Turn the air conditioner to the "on" position and set controls to the coldest setting. Start the engine and allow to idle. Then open the hood and inspect the clutch at the front of the compressor, is it turning? "Engaged" if so, the system has enough refrigerant to activate. If the system is low on refrigerant it will not work properly. In this case an air conditioner recharge kit is needed to recharge the system. If the system is low on refrigerant it could cycle on and off, making a ticking noise. If the compressor clutch is not turning proceed to next step.

3. Inspect for Refrigerant Leaks - If the system has a large leak and no refrigerant remains it will not activate. First test system for a static pressure charge, with the engine off attach an ac gauge to the low side pressure port and check the state of charge. Depending on outside temperature there should be between 50 psi and 80 psi. (Cool and warm). A refrigerant leak detector is needed to inspect for leak, but if you do not have a leak detector there is an alternative method. The air conditioner system is designed to run with oil suspended in the refrigerant to lubricate the system. Check for oily residue outside the system by inspecting all hoses, compressor, condenser, evaporator or receiver drier and replace any component that has failed.

4. Inspect Fuses - Check under dash panel and under hood power distribution center. Replace failed fuses as needed, recheck system. If the new fuse fails when reinstalled a short circuit is present and requires diagnosing with a wiring schematic, follow circuits to locate short, repair as needed and recheck system.

5. Check Temperature Control Vents - The vents inside your car are controlled by a cable, electrical servo or vacuum servo. If the temperature blend door is not functioning properly it will cause warm air from the heater to exit the vents. To check this start the car and allow the engine idle, next turn the blower motor speed on low, switch the temperature control from warm to cold while your ear is close to the vents. You should hear the door move inside the heater box as it swings from open to close. If not, insect for a vacuum leak or a shorted motor in the servo, repair the leak or replace the servo motor.

Nov 18, 2008 | 2001 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...