Question about 1999 Dodge Intrepid

1 Answer

How do I change the alternator on a 1999 dodge intrepid

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 17,970 Answers

Check thid procedure... Removal & Installation

2.7L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Lower plastic splash shield Transmission cooler and position it aside Lower radiator crossmember support
  3. Loosen but do not remove:
    Adjusting -T- bolt and the pivot bolt Drive belt adjusting bolt
  4. Remove or disconnect the following:
    Drive belt Alternator field circuit plug Alternator B+ terminal nut and wire Pivot bolt; be careful not to lose the spacer Alternator

    how do I change the alternator on a 1999 dodge - zjlimited_992.jpg

    Fig. The location of the generator on the 2.7L Engine

To install:
  1. Install or connect the following:
    Alternator Pivot bolt with the spacer and leave loose Alternator field circuit plug Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm) Drive belt
  2. Using a belt tension gauge, torque the adjusting -T- bolt until the tension gauge reads 120 lbs. (534 N) for a used belt or 180-200 lbs. (792-880 N) for a new belt.
    Lower radiator crossmember support Transmission cooler Lower plastic splash shield Negative battery cable
  3. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).

3.2L & 3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.

  2. Remove or disconnect the following:
    Negative battery cable Lower mounting bolt and pivot bolt Drive belt tension bolt Drive belt Bracket, lower mounting bolt and pivot bolt Alternator Alternator field circuit plug Alternator B+ terminal nut and wire

    zjlimited_993.jpg

    Fig. The location of the generator on the 3.2L and 3.5L engines

To install:
  1. Install or connect the following:
    Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm) Alternator field circuit plug Alternator Drive belt Pivot bolt and lower mounting bolt
  2. Using a belt tension gauge, torque the -V- drive belt until the tension gauge reads 120 lbs. (534 N) for a used belt or 140-160 lbs. (623-711 N) for a new belt.
  3. Using a belt tension gauge, torque the Poly -V- belt until the tension gauge reads 120 lbs. (534 N) for a used belt or 180-200 lbs. (792-880 N) for a new belt.
  4. Install the bracket.
  5. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm)
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).
  6. Connect the negative battery cable.

Hope this helps (remember to rate tna domment this answer).

Posted on Apr 09, 2011

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Lady_Chaos
  • 21 Answers

SOURCE: need to change the alternator

REMOVAL & INSTALLATION

3.3L Engine:

  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Posted on Jan 30, 2009

SOURCE: THERMOSTAT PICTUREDIAGRAM OF 1999 DODGE INTREPID, 2.7 ENGINE SIZE

Thanks for your help. But I got the answer that I need.

Posted on Oct 21, 2008

Lady_Chaos
  • 21 Answers

SOURCE: need to install an alternator

Removal & Installation
2.7L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Lower plastic splash shield
    • Transmission cooler and position it aside
    • Lower radiator crossmember support
  3. Loosen but do not remove:
    • Adjusting “T” bolt and the pivot bolt
    • Drive belt adjusting bolt
  4. Remove or disconnect the following:
    • Drive belt
    • Alternator field circuit plug
    • Alternator B+ terminal nut and wire
    • Pivot bolt; be careful not to lose the spacer
    • Alternator 0900c152801d4a1e.jpg
    (The location of the generator/alternator on the 2.7L Engine)
To install:
  1. Install or connect the following:
    • Alternator
    • Pivot bolt with the spacer and leave loose
    • Alternator field circuit plug
    • Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm)
    • Drive belt
  2. Usinga belt tension gauge, torque the adjusting “T” bolt until the tensiongauge reads 120 lbs. (534 N) for a used belt or 180–200 lbs. (792–880N) for a new belt.
    • Lower radiator crossmember support
    • Transmission cooler
    • Lower plastic splash shield
    • Negative battery cable
  3. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).

--------------------------------------------------------------------------------------------------------------------------------------------------
3.2L And 3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Lower mounting bolt and pivot bolt
    • Drive belt tension bolt
    • Drive belt
    • Bracket, lower mounting bolt and pivot bolt
    • Alternator
    • Alternator field circuit plug
    • Alternator B+ terminal nut and wire 0900c152801d4a1f.jpg
    (The location of the generator/alternator on the 3.2L and 3.5L engines)
To install:
  1. Install or connect the following:
    • Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm)
    • Alternator field circuit plug
    • Alternator
    • Drive belt
    • Pivot bolt and lower mounting bolt
  2. Usinga belt tension gauge, torque the “V” drive belt until the tension gaugereads 120 lbs. (534 N) for a used belt or 140–160 lbs. (623–711 N) fora new belt.
  3. Using a belt tension gauge, torque the Poly “V”belt until the tension gauge reads 120 lbs. (534 N) for a used belt or180–200 lbs. (792–880 N) for a new belt.
  4. Install the bracket.
  5. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).
  6. Connect the negative battery cable.
Hope this is what you were looking for.

Posted on Jan 30, 2009

csmock132
  • 4669 Answers

SOURCE: find location for oil filter for oil filter for dodge intrepid

What engine? 2.7 passenger side on the bottom next to oil pan. 3.2 and 3.5 Drivers side coming off the side of block, near the front under the exhaust manifold.

Posted on Mar 24, 2009

heavymetal77
  • 721 Answers

SOURCE: changing the water pump on a 1999 dodge intrepid

Good luck! I can't type out the entire process but you need alot of tools,some chrysler only tools,a good manual,since you never did it before,coolant,the pump,new timing belt,a torque wrench for the timing belt tensioner,etc. Leave it to a pro.

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a serpentine belt on a 1999 intrepid?? Does the alternator need to be loosened??


The alternator does not have to be loosened.

The tensioner mount has a square hole in it for inserting a ratchet or a breaker bar. Pull the tensioner in the direction which realeases the tension on the serpentine belt.

Charlie

Jan 08, 2011 | 1999 Dodge Intrepid

1 Answer

Where is the altenator located on a 1999 dodge intrepid


IT IS ON THE FRONT OF THE ENGINE, HERE IS A PICTURE OF THE ALTERNATOR.


63f47b1.jpg

May 12, 2010 | 1999 Dodge Intrepid

1 Answer

99 dodge intrepid 2.7 engine, only runs when connected to jumper cables. where is the alternator located, could this be the issue or electrical problems


Definately could be the issue. The alternator should be located on the passenger side of the car at the front of the engine. Look for the belt-it will be going around the alternator pulley. IF you can take it off you can take it to Auto Zone (or one of the other guys) and get it tested.

Mar 12, 2010 | 1999 Dodge Intrepid

1 Answer

Where is the alternator located on the dodge 1999 intrepid?


Face the motor looking at the belt. Its the very bottom to the left of the crank.

Hope this helps. =)

Oct 22, 2009 | 1999 Dodge Intrepid

1 Answer

How do I remove the alternator on a 1999 Intrepid with a 2.7L engine


remove belt from pulleys use a wrench on the tensioner to get belt off then remove mounting bolts on alternator should be a diagram of pulleys under the hood to tell you where the tensioner is

Sep 29, 2009 | 1999 Dodge Intrepid

1 Answer

1999 dodge intrepid, battery light on, replaced battery and engine computer, light still on. Is there a reset? What else can cause this dash light to come on?


If your alternator is going bad the battery indicator light will come on your dash. I did the same thing before thinking my battery was bad and buying a new one. Turns out it was the alternator. Hope this helps..

Jul 19, 2009 | 1999 Dodge Intrepid

1 Answer

Alternator will not move


Did you loosen the nut or bolt that is in the bracket with the alternator? It has tension on it also...

Mar 29, 2009 | 1999 Dodge Intrepid

1 Answer

How to change spark plugs in 2001 intrepid


look for 1 inch black boxes near the top of your engine pull up on them plugs should be there

Jan 19, 2009 | 1999 Dodge Intrepid

1 Answer

Where is the oil sending unit on a 1999 Dodge Intrepid?


I think it on the lower left side of block look from under car

Jan 14, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

1,085 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...