Question about Lincoln LS

2 Answers

My abs and traction control lights are on where are the wires for that located?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,654 Answers

Check the wheels for a loose sensor, each wheel has a sensor attatched to the back of the rotors or drums that measure wheel speed. Usually a sensor has gone bad or came loose when this happens.

Posted on Apr 09, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 7,782 Answers

Please see my tip at http://www.fixya.com/cars/r6003525-abs_traction_control_lights . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Posted on Apr 09, 2011

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1071 Answers

SOURCE: bmw 530i 2001 abs and traction control light on

abs control module is bad

Posted on Aug 19, 2009

Testimonial: "thanks how much is an abs module cost and is it necessary to fix right away"

  • 1 Answer

SOURCE: abs light/traction control light

You can check out what the trouble code is by pushing and holding the information button and the up arrow (right side of instrument cluster above the radio) until all the instrument clusters light. Press the information button (last) to enter test mode. I've had an error C1234, meaning Left rear wheel sensor fault. I found the problem to be a corroded connector under the chasis just under the rear left door about 2 feet in. I had to by-pass (replace 1 wire due to corrosion at the connector.

Posted on Sep 15, 2009

godrock00
  • 1 Answer

SOURCE: traction control light and abs light

Something happened to me today... I was driving my car and my trac control and abs were on.... I put my car in reverse and got out of a parking... And the traction control and abs went off... What could that be?

Posted on Aug 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Light abs traction control stays 1998 buick park avenue


PRE-DIAGNOSTIC INSPECTIONBefore diagnosing ABS/TCS, perform a comprehensive visual inspection of system as follows.Check ABS/TCS wiring harness connectors for looseness. Check harness routing; pay particular attention to wheel speed sensor wiring harness routing. Check fuses No. 1D, 5B and 6B in instrument panel fuse block. Check fuses No. 1 and 2 in underhood fuse block. Check brake fluid level in master cylinder reservoir. Check brake fluid level in Pressure Modulator Valve (PMV) assembly reservoir. Ensure parking brake is fully released. Ensure parking brake switch is functioning properly. Always perform ABS/TCS system functional check before using DIAGNOSTIC CODE CHARTSThe EBCM/EBTCM has self-diagnostic capability, which can detect system failures. Fault codes stored by EBCM/EBTCM can be displayed using Tech 1 scan tester. There are no provisions for flash code diagnostics.Begin ABS/TCS diagnosis with PRE-DIAGNOSTIC INSPECTION procedure. If failures are found during pre-diagnostic inspection, perform necessary repairs, and proceed with ABS/TCS FUNCTIONAL CHECK. See Fig. 5 .If no failures are found during pre-diagnostic inspection, go to ABS/TCS FUNCTIONAL CHECK. See Fig. 5 . The ABS/TCS FUNCTIONAL CHECK will either indicate ABS/TCS is functioning properly or direct technician to various diagnostic procedures such as diagnostic charts, symptom diagnosis or BRAKE warning light diagnosis.CHART D - TRACTION OFF WARNING LIGHT ON CONTINUOUSLY & NO DTC SET (BUICK WITH UH8 OR U2A INSTRUMENT CLUSTER)Circuit DescriptionWhen ignition switch is first turned to RUN position, EBTCM goes through a self-test, which lasts 2-4 seconds. During self-test, EBTCM commands TRACTION OFF indicator warning light on. Powertrain Control Module (PCM) can also command EBTCM to set a Code 75 which will illuminate TRACTION OFF indicator.Traction control switch is located either on instrument panel center trim plate or driver's front door trim panel. Switch allows driver to select traction control mode (on/off). When traction control system is turned off, TRACTION OFF warning light comes on.EBTCM monitors transaxle temperature through

Jul 12, 2014 | 1998 Buick Park Avenue

1 Answer

ABS traction control sensor location


I have another question: Where can I find the VSS analog speed signal for the
Perodua Myvi 2013? Thanks a lot. David

Dec 26, 2013 | Cars & Trucks

1 Answer

Traction control light on ,brake light on ,abs light on


If the brake light is on, check the fluid level immediately and add fluid if necessary.
After that, have the car's OBD-II computer scanned with a 'Brake Scan' tool for OBD-II. This will help to narrow down which wheel speed sensor is giving you trouble. It might be a broken wire, or a bad wheel speed sensor.

The wheel speed sensor sends information to the ABS side and the Traction Control side of the computer module for ABS and Traction Control.

The car will revert to standard braking and regular non braking transmission power distribution to the drive wheels when the ABS and Traction Control lights are both on.

Good luck on this repair.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

2004 Monte Carlo "Trac off" light is on and "service traction system" warning is on and dinging. ABS light is also on. I was given code c1214 and c1226 software EBCM up-date? What is the problem?


The traction control and abs are both activated by the abs sensors located at all four wheels. It is common for those sensors to get covered in brake dust and get false or no signal. Also the wiring connections can become corroded over time. I am not sure what the codes are for but checking the sensors/wiring are where I would start.

Apr 23, 2010 | 2004 Chevrolet Monte Carlo

3 Answers

Where is the abs speed sensor on a 5 series bmw?as the abs light and traction light have both illuminated


You have 4 wheel speed sensors. There is one at each wheel located just behind the hub. You can trace it by loacting the black insulated wire leading out from the wheel well and going behind the wheel.

Mar 27, 2010 | 2001 BMW 5 Series

1 Answer

Engine light and ABS traction control light remain


The ABS sensor is a speed sensor also for Traction Control. This is why both lights are on , One of your front ABS sensors are bad or disconnected, or has a pinched wire.

Jan 16, 2010 | 2000 Chrysler 300M

2 Answers

Abs light on all the time ,occasional brake light ,traction off light on all the time


I would suggest u take ur vehicle in to a reputable dealer this could be a dangerous situatio should u get into an auto accident.

Oct 02, 2009 | 2005 Chrysler Pacifica

1 Answer

ABS TURN LIGHTS COME ON


need to get abs codes read. it will tell you what wheel to look at.
1.bad wheel bearing, sensor is part of bearing.
2.broken wires to sensor.
3.traction control part of abs

May 06, 2009 | 2004 Cadillac CTS

1 Answer

Traction Contrl and ABS Light on


No, it is probably not related. Usually the ABS and traction control light is either a wheel sensor problem, located in one of the wheel bearings, or most likely in the wire harness from the wheel bearing sensor. Remove wires and spray clean with a good solvent electric spray, and check the condition of the receptacle. I have had these problems with my 02 AWD so many times it has become almost routine. GM really have a problem with this type of speed sensor in the wheel bearings. In the AWD model, it keeps the car in FWD if the ABS light is on for any reason. JUNK!

Nov 19, 2008 | 2002 Chevrolet Venture Passanger

1 Answer

Abs light and traction control light cant figure out why?


clean ringer at wheel end..be sure you did not disturb alignment of sensor (VSS) which tells 'puter wheel speed for ABS and traction control

Oct 29, 2008 | 2002 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...