Question about 1998 GMC Blazer

1 Answer

Cv shaft passangers side how to remove have hub assembly off have to replace both

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 72 Answers

You will have to take the steering knuckle completely out of the way, which requires getting the ball joints loose from the knuckle. You will also have to take the bottom bolt out of the shock because there is not enough clearance to get past it. The Blazers had two different was of holding the CV shafts to the front axle housing, a series of 15mm bolts or a retainer clip on the shaft that goes into the differential. If you don't see bolts, then you should be able to pop the CV shaft out with a pry bar. Give it a few good shoves to reinstall the new shaft.
Hope this helps. Good luck!

Posted on Apr 09, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

2 Answers

On my 97 the abs ring on the cv axle is almost gone!! made a turn today and the wheel almost locked up..any help??


I would have the cv axle changed along with any integral parts such as the abs ring.

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the wheel cover/hub cover from the wheel and tire assembly, then loosen the lug nuts. Fig. 1: After removing the wheel/hub cover, loosen the lug nuts 86877115.gif

  3. Raise and safely support the vehicle, then remove the wheel and tire assembly. Insert a steel rod in the rotor to prevent it from turning, then remove the hub nut and washer. Discard the old hub nut. Fig. 2: Before removing the hub nut and washer, insert a steel rod in the rotor to prevent it from turning 86877116.gif
    Fig. 3: Remove the hub nut and washer, then discard the nut, and replace with a new one during installation 86877117.gif

  4. Remove the nut from the ball joint to steering knuckle attaching bolts.
  5. Drive the bolt out of the steering knuckle using a punch and hammer. Discard this bolt and nut after removal. Fig. 4: Drive the bolt out of the front wheel knuckle using a punch and hammer, then discard the nut and bolt and replace with new ones during installation 86877118.gif

  6. If equipped with anti-lock brakes, remove the anti-lock brake sensor and position it aside. If equipped with air suspension, remove the height sensor bracket retaining bolt and wire sensor bracket to inner fender. Position the sensor link aside. Fig. 5: If so equipped, remove the anti-lock brake sensor and position it aside 86877119.gif

  7. Separate the ball joint from the steering knuckle using a suitable prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing. Use care to prevent damage to the ball joint boot. Remove the stabilizer bar link at the stabilizer bar. Fig. 6: When separating the ball joint from the steering knuckle, be careful not to damage to ball joint boot 86877120.gif
    1. Slide the link shaft out of the transaxle. Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, damage to the outboard CV-joint may occur.
    2. Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent. NOTE: Never use a hammer to separate the outboard CV-joint stub shaft from the hub. Damage to the CV-joint threads and internal components may result. The halfshaft assembly is removed as a complete unit.
    3. Install the CV-joint puller tool T86P-3514-A1 or equivalent, between CV-joint and transaxle case. Turn the steering hub and/or wire strut assembly aside.
    4. Screw extension tool T86P-3514-A2 or equivalent, into the CV-joint puller and hand tighten. Screw an impact slide hammer onto the extension and remove the CV-joint.
    5. Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, damage to the outboard CV-joint may occur.
    6. Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent.
    7. Remove the halfshaft assembly from the vehicle. Fig. 7: These tools are necessary for halfshaft removal 86877121.gif
      Fig. 8: Installing the specified tools to remove the halfshaft assembly from the vehicle 86877122.gif
      Fig. 9: Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, since damage to the outboard CV-joint may occur 86877123.gif
      Fig. 10: Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent, and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent, then remove the halfshaft assembly from the vehicle 86877124.gif
      Fig. 11: Exploded view of the halfshaft assemblies and related components - automatic transaxle 86877125.gif
prev.gif next.gif

Oct 26, 2010 | 1997 Lincoln Continental

1 Answer

Replace velocity axle assembly passanger side


In order for the cv shaft to come out the rotor assembly has to be disconnected from the center shaft ie remove center wheel nut and all other components attached to the rotor assembly except the ball joint and seperate it from the shaft.
shaft might be held in place with circlip[s or will just slide out with a hard pull.

Sep 21, 2010 | 2000 Toyota Camry

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

3 Answers

How to replace front cv shafts on a 1997 isuzu rodeo ?


Remove tire, remove axle nut, pop ball joint off, remove clip, pull axle

For a more detailed instructions, go to autozone.com and register for free.
Now you will have full free online repair manual

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

I have a 1997 Dodge Ram 1500 4 wheel drive. I


i have found that you need to first make sure the cv shaft is moving free in the bearing. soak everything with penitrating oil. you should be able to move shaft in & out a little. the hub is a very tight fit. you need to tap it some from side to side untill you see a little gap between hub and spindel. then place the head of a flat screw driver in that gap and all around the hub, prying back and forth where ever possible. soak, tap and pry all over. be hard on it if replacing, more gentle if not. good luck.

Jul 17, 2009 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

Wheel Shaking


Sounds like the tie rod is worn. It is common when a CV shaft goes bad that it wears out the tie rods as well. the tie rods hold the wheel in posiition and that why you get the movement 3cm left to right. The tie rod is on the upper part of the wheel hub and if you grab it where it meets the wheel, give it a good shake. If there is movement replace it.

Joe

May 28, 2009 | 1991 Honda Civic

1 Answer

Replacing CV Joints


Yes you can remove the drive shaft by unbolting the bottom ball joint,then removing the nut that holds the shaft in the hub I would'nt recommend trying to replace just the CV joint as this can be a very complicated procedure involving specialized tools and more than just general mechanical skill,this isn't true of all,as some CV's come apart fairly easily.If the joint is bad you should probably just replace the axle.Remember to match mark any adjustable parts you may have to disassemble,and when you reassemble make sure to check the splines of the shaft and the drive hub,remove any foreign material and carefully file or sand any burs or scratches,any of these can cause the spline to bind on reassembly and possibly cause irreparable damage to one or both parts.Good luck hope this helps.

Apr 10, 2009 | Hyundai Motor 1998 Sonata

2 Answers

Drive Axle Vibration


prob have a bad shaft, not balanced properly

Feb 18, 2009 | 2003 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...