Question about Chevrolet S 10

1 Answer

What motors will fit into a 1985 chevrolet s-10 without changing the whole front end

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 120 Answers

Dont know all the possibilties , iknow you can put a small block in it with a kit ,sure most performance places sell them or reckon you put a v6 in it if you dont have one but if you get a electronic engine wiring will be a chore and you must get everything related to that engine including ECM unless you put a carb and intake on it which they make for a 2,8 v6 but pretty pricy

Posted on Apr 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 99 s-10 the brake line has rusted through just above rear the axle on driver side. Do I need to change the line all the way to the front juntion block?


I would advise you to change the whole line. You can cut it and install a fitting and a short line but this will be a potential leak. Hope this helps. Good luck.

Jan 09, 2011 | 1999 Chevrolet S-10 Pickup

1 Answer

Gas line is leaking, can i splice it or do I need to replace the whole line?


you can splice it, use a tube cutter and cut at a sextion where the line is good, use hi strenght fuel injection hose and clamps, use two clamps at each end, and fasten against vibration

Aug 19, 2010 | 1985 Chevrolet S-10

1 Answer

Will a 1985 S10 blazer tilt steering collum fit a


yepper! lol i have owed 5 of this geneation and both the s-10 and blazer are identical in the dash, engin and drive train

Jun 05, 2010 | 1988 Chevrolet S-10

1 Answer

I have a 1986 S10 extended cab, that has had the whole front end wrecked, I found a 1991 S10 that the guy only wants $500 dollars for, and I would like to use it for parts to fix my current 1986 S10, I...


Yes, those fenders, etc. should be fine. Those two trucks are the same. The body didn't change until 1994 and the part numbers for the two trucks' fenders are identical all the way through 1993. Good luck! I hope this helps.

Feb 03, 2010 | 1984 Chevrolet S-10

1 Answer

Is there ANY way to change the oil pan gasket on a S10...


Remove motor mount bolts and rear transmission crossmember bolts or nuts,suppport engine/trans. see if u have enough clearance between pan and axle remove pan. if not, split the exh away from the manifolds. worth a try

Dec 22, 2009 | 2001 Chevrolet S-10

1 Answer

Will shocks for 1985 s10 fit a 2002 s-10


Yes, as long as the 85 S10 and 2002 S10 are both the same as in  2WD or 4WD.
I believe the rear shocks are the same but the front shocks are different between the 2WD and 4WD.
Good luck and hope this helps.

May 05, 2009 | 2002 Chevrolet S-10

1 Answer

HELP!!! Trying to Remove oil pan from 1985 Cheve


wow! that really sucks.... first if you drop the cross member you should be able to get at with ease other wise if you dont wanna screw with that unbolt the engine mounts and raise the front of the engine up BUT THIS TIME WATCH THE DISTRIBUTOR.... dont get near the fire wall... get me informed of other problems. and there aint no good way of taking the motor mounts out just take a wrench and put it on the bottom nut and take an impact wrench to the bolt

Feb 27, 2009 | 1985 Chevrolet S-10

1 Answer

Motor swap 88?


It sure Won't The Bolt Patterns are Different. And you will need to Cut out the Fender Wells to get the 350 to fit and use Hugger Headers and they would be a REALLY Tight Squeeze. I have seen it done though. Also the Rear End would Shell out unless you put a 12 Bolt in it.

Jan 25, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Removing emgine to change clutch plate in 1985 honda civic 1300 lx


I assume you are talking about the clutch to the transmission. They make a tool that will support the engine and allow you to remove the gearbox on most cars without removing the engine. It is a tight fit but much less work.

Aug 09, 2008 | 1985 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...