Question about 1995 Dodge Neon

3 Answers

Drained break fluid and pedal goes to floor, i have a 95 dodge neon i also have Bleed all the wheels starting with the rear pass side it is normally the furthest from the master cyl then the other rear then front pass then driver front. Bleed until clean fluid is coming from wheel cylinders. Still nothing I noticed that there is a air tube right next to the master cylinder and it does get better when i take the cover off but then it goes right back to normal when i put it back on any suggestions?

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

On a Neon you do the passenger side rear, then drivers side front, then drivers side rear and then passenger side front.

Posted on Nov 30, 2012

  • maxcanon57 Nov 30, 2012

    On a Neon you do the passenger side rear, then drivers side front, then drivers side rear and then passenger side front.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 249 Answers

If there are no visibal leaks then it probably needs a master cylinder leaks from the brake lines

Posted on Apr 09, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Start from the rear driver side, and then the rear passenger side, and the front passenger side,and then the driver side make sure you keep plenty of fluid in the master cylinder during bleeding proccess

Posted on Apr 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hissing brakes


IT is probably a vacuum leak in the brake booster. With the pedal going to the floor There is either no brake fluid or you will have to bleed the system. Replace the booster and bleed the brakes starting at the longest line first

Oct 08, 2013 | Dodge Neon Cars & Trucks

1 Answer

How to bleed brakes on a 2008 dodge caravan


first you need to make sure you can open all bleeders on each wheel.You will need 2 people,1 to open and close bleeder and 1 to pump and hold pedal down.Be carefull,bleeders that haavnt been opened in a while can break off.Spray them with PB Blaster and let them sit for while.Then you start with pass rear then drivers rear then pass front then drivers font in that order.Make sure master is full of fluid,then have person pump brakes 5 to 7 times and hold them on,then open bleeder until the pedal is down to floor.Make sure person pushing pedal lets you close the bleeder before letting pedal up to pump it again.Repeat this until there is no air coming out of bleeder.If they let pedal up and you havnt closed the bleeder, it will **** air back into system.

Nov 13, 2012 | 2008 Dodge Grand Caravan

1 Answer

Changed brake pads and now I have no brake pressure


you may need to bleed your breaks so check your fluid and have a friend help you with this.. open or take off break fluid cap and top off with fluid leave cap off and start on the back passanger side break have someone pump the break a few times and then hold down on the break pedal while you open the bleeder valve when the break pedal reaches the floor hold there and retighten the bleeder valve and repeat untill no air only fluid comes out, then move to the driverside rear wheel and repeat,next is the front passanger side wheel then finaly front driverside wheel. check fluid in master cylender after every 2 trys on each wheel to make sure pleanty of fluid is in resourvior so your not putting air in the lines.. you should see a video on this to make sure you understad it fully before attempting yourself, go to youtube videos and watch a video on how to bleed breaks almost all break systems are the same. i hope this helps.

Jul 24, 2011 | 2000 Mitsubishi Mirage

1 Answer

I cant get the air to bleed out of my brakes on a 1997 dodge dakota i put on a new master cylender and have been bleeding them for 2 days they seem to bleed normal when truck is not running pump up and...


You need a helper, to slowly press the brake pedal down, as you open bleeder valve,then close before your helper gets near the floor.
Repeat until all air is out of each wheel position.
RR,LR,RF then LF. Always start from the farthest wheel and have motor running
Never pump brakes. That does nothing at all.

Nov 03, 2010 | 1997 Dodge Dakota

2 Answers

How to bleed the brakes on a1999 chevrolet venture van instaslled new brake pads on front tired to bleed brake pedal all the way up when van not running - goes to floor when van is running


Start with brake in the rear that is the farthest away from the master cylinder ( if your master cylinder is on drivers side start with passenger rear,pump up brake pedal until hard have someone else open bleeder valve until air or fluid squirts out,while holding brake pressure even if goes to the floor dont release pedal until bleeder valve is tightened or you will **** air back into the line,do this several times making sure you get a full stream of brake fluid and no air,continue to other rear wheel and then proceed to front wheel furthest from master cylinderand then final wheel. if you still don't have brakes change master cylinder and bleed all brakes again.

Jul 05, 2010 | 2000 Chevrolet Venture

2 Answers

2001.5 Dodge Ram Diesel 2500 4x4 Brake Pedal drops to floor


It sounds like you have a bad mastercylinder cause when you panic brake it doesn't have time to bleed through the valve in the cylinder but under normal braking your foot is on pedal longer in turn giving the fluid time to bypass the valve in the mastercylinder in turn the pedal going to the floor.

Apr 21, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

Our kia amanti's breaks build up and stop the car, then when we use a wrench and blead the line under the hood the breaks start working normally again.


do you mean that you pump the brakes to build up pressure in order to stop?

bleeding brakes requires you to bleed them from each wheel starting at the right rear. procede as follows: have someone sit in the drivers seat. have them pump the brakes slowly and forceably to build up pressure. maintain force on the pedal. starting at the right rear, open the bleed screw slowly. the pedal will go to the floor and the fluid will drain. hold the pedal to the floor and tighten the bleed screw. repeat this procedure several times until you are sure there is no air in the line. follow these steps at each wheel- left rear, right front, left front. keep reservoir filled with fluid. fill after each wheel. (note) get a length of rubber hose that fits snuggly over the end of the bleed screw
and drain fluid into a container.

i think you were draining the anti-lock brake system. in which, case follow the steps above for that also.

Feb 25, 2010 | 2005 Kia Amanti

2 Answers

How do I bleed air from the brakes


Two persons are required: one to bleed and other to press brake pedal.
Remove wheel and hub of the side you want to bleed. You will find the bleed nut there. Open it a little until some oil flows out. Ask the other person to press brake pedal with steady pushing and withdrawing until he feels its tight while you slowly tighten the nut. Adjust tightness of pedal by trial. Don't forge to refill the brake fluid after bleeding all the brakes.

Do give my solution the highest rating if it solves your problem. Thank you for using fixya!

Aug 07, 2009 | 1989 Volvo 240

3 Answers

Replaced front brkes how do i bleed them


are they hard or soft to break at the pedal? or normal? if normal NO if soft/squishy YES if too hard... drain some fluid? or check master break cil.

short answer: only need to if there is something wrong.

Aug 06, 2009 | 2000 Mercury Mystique

2 Answers

Changed break line but still have no pressure in breaks


to do a complete job. you need to bleed all 4 wheels, starting from Right Rear. Right front. Left Rear. Left Front.

Apr 07, 2009 | 1995 Chevrolet Silverado 2500

Not finding what you are looking for?
1995 Dodge Neon Logo

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...