Question about 2004 Dodge Stratus

1 Answer

My battery light cam on and then after 50 miles the battery was dead with no power. Is there a way to get the code on my odometer like I did when my check engine light came on?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 4,977 Answers

It sounds like you have a charging system problem either the alternator or the computer has a problem with grounding the charging system.if the charging system was okay then while you were driving it would have been able to supply power without the battery going dead were as if it was the battery the car wouldn`t start.you can try to pull the code out the same way and see happens.

Posted on Apr 08, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2007 Mazda cx-7 completely dead for no reason on and off


hi
cam shaft sensor got nothing to do with your oil change.
Cam runs on your timing belt. it's a possibility that it may be faulty as its only a sensor.
change the sensor

Apr 29, 2017 | Mazda CX-7 Cars & Trucks

1 Answer

My 2003 chrysler town and country just put up code p1698 through my trip odometer what is 1698 mean?


1684= BATTERY DISCONNECTED WITHIN LAST 50 MILES.
1698 PCM FAILURE EEPROM WRITE DENIED ALSO
1698 NO CCD MESSAGES FROM TCM/ OR BCM

Nov 09, 2013 | 2003 Chrysler Town & Country

1 Answer

2004 chrysler pacifica no power even after jump


check for a bad connection like a bad ground at the battery, make sure both terminals are tight at the battery, the starter and the ground at the engine. the shop that installed the EGR should have erased the codes, after 50 to 100 miles you would be able to go through emissions.

Sep 01, 2012 | Chrysler Pacifica Cars & Trucks

2 Answers

Get "Service Engine Soon" light after car was


Purchase a OBD2 code reader for $50-$100. Scan for codes and let me know what Diagnostic Trouble Codes are active.

Mar 27, 2011 | 2002 Saturn L-Series

1 Answer

I have an '01 PT Cruiser with 115,000 + miles. The car runs fine for about 15 miles then stalls. Car will not start for about 10-15 minutes. When car starts, it runs perfectly for another 10-15 miles. I...


If you have an electronic display in the bottom half of your odometer (speedometer) try getting the fault code displayed...key in the ignition (do not try to start the car) then switch from off, then on, then off, then on then off then on and leave on...take note of the four digit number(s) prefixed with a letter (most often a 'P') in the bottom display. P0340 for example means a dead cam sensor fault. My guess is that it is your cam sensor that is faulty rather than the crank sensor as mentioned, but read the codes and then simple post the number on google ("Chrysler PXXXX error code") to find the explanation of what it means. A couple of bolts (supplied) and about $30 for new cam sensor is all that should be needed

Sep 10, 2010 | Chrysler PT Cruiser Cars & Trucks

1 Answer

I left my truck rest for 12 days when I returned and drove it 50 miles the battery light came on and the elecrical gauge dropped to between 9 and 14. I drove it home another 34 miles and when I got home...


Likely a battery problem. Batteries tend to fail when they sit for a while. If your electrical guage was reading 9 - 14, with a dead battery, the alternator was working. Also, if the alternator was dead, you'd likely have noticed dimming headlights and other electrical issues.

But, you could take the battery to AutoZone and let them check it - free.

Jul 25, 2009 | 2000 Chevrolet S-10

1 Answer

Speedometer & odometer not working after dead battery replacment


Remove the - (Negative) battery lead and wait for a few seconds. the refit BUT DONT LET the terminal arc keep it firmly pressed on while tightening. It seem as if this may have happened when you fitted the new battery as any rapid on off power to the management system will scramble it. You also dont say if you have driven it far as some times after a battery change depending on management system fitted around 20 miles before system workks out settings lost when power removed (happens after a sensor change aswell) hope this helps.

Jul 08, 2009 | 1997 Ford Escort

1 Answer

Car isn't starting


I was have this problem. Battery is low. Charge battery or use cable to start. You can check the problem using Diagnostic Trouble Code. Cycle ignition key On - Off - On - Off - On within 5 sec. The odometer will show teh P-code for the DCT code number. Error code for low battery is P0562. Only "DONE" displayed on odometer inicates that no DTCs are present (no error) and the procedure is completed. PCM memory has been cleared within the last 50 ignition cycles. Hello from Croatia.

Apr 29, 2009 | 1999 Chrysler 300M

1 Answer

Check engine light


Code 12.................Problem with the battery connection. Direct battery input to PCM disconnected within the last 50 ignition key-on cycles.

either a loose connection or the battery dead or removed within 50 last times you turned on the car, check battery terminals for corrosion or loose connector, and check the earth wire for corrosion, the code will dissapear by itself if the power is not removed again

Apr 11, 2009 | 1995 Chrysler Cirrus

1 Answer

Jeep cherokee


Hello,

I'm not sure which sensor you replaced on your Jeep. I will assume you had diagnostics run and replaced a sensor based on a trouble code.

Run self-diagnostics--

Observing the odometer display...

Turn the Key On, Off, On, Off, and On again (three times, just to the point where the dash warning lights come NOT Engine Cranking).

Now diagnostic trouble codes will display where miles is normally displayed in the odometer. Write down these codes. Note- If you lose track of the codes or wish to double/triple check the codes, simply turn the Key Off and start over.

Now clear the codes by disconnecting the negative battery cable for five minutes.

Reconnect the battery cable and check the codes.again. There should not be any codes UNLESS- there is a fault the computer (PCM) recognizes immediately OR you were unsuccessful erasing the codes. IF there are less codes than when you began, the erase was successful but there is still a problem.

To stop nitpicking, I'm going to assume there are no trouble codes displayed after clearing the codes and reconnecting the battery. Now test drive to see if the code comes back. If no codes appear after a few days (approximately 50 miles, although the threshold is more complicated than I need to get into) it appears your repair was successful.

Update us as necessary on your problem.

Nov 17, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Dodge Stratus Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...