Question about 1989 Chevrolet K1500

2 Answers

Where is the bleeder screw for a 1989 silverado/power steering

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,763 Answers

There is no bleeder screw, you will need to top of fluid then start engine turn wheel all the way right and left then shut off eng and check fluid level, top off again if needed, if you are getting a howling noise due to a repair to the system then it will go away after a little driving and air is purged from system, this is done automaticly. if theres still a noise then the pump will need to be replaced and some aftermarket pumps will make a small amount of noise but not alot. good day.

Posted on Apr 08, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

I'm not sure i understand what your asking exactly ...There is no bleeder on the power steering .
Just fill the reservoir on the pump and turn the wheels back and forth with the lid off and burp the air out and top it off as needed.

Posted on Apr 08, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed 89 ford ranger 4x4 clutch


there is a bleeder screw by the transmission slave cylinder that you bleed the air out.just pump the clutch pedal a few times hold the pedal to the floor and have someone crack open the bleeder screw to bleed the air out then close it and repeat.make sure the master cylinder for the clutch doesn`t go low.

Nov 02, 2011 | 1989 Ford Ranger

1 Answer

I replaced all my brake lines. How do I bleed the air out?


Make one guy in string side
Let him push the break
Have assistant pump brake pedal and hold approx. 2/3 down
Open bleeder screw and observe bubbles in container
Close bleeder screw and repeat until no bubble are observed
Repeat at next wheel
Make sure master cylinder does not empty during procedure.

Jun 03, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

REPLACED REAR HYDRAULIC BRAKE CYLINDER. CAN'T BLEED BRAKES


make sure fluid full lid on.open bleed screw put finger over hole in end of bleeder,have someone slowly pump break pedal whule finger still on bleeder.8/10 times.should start to get fluid.top master up.open bleeder depress pedal slowly close bleeder while pedal down.release pedal and repeat.if system ran dry few more steps lrt me know.

Feb 17, 2011 | 1989 Buick Park Avenue

2 Answers

We can not get all brakes to bleed..what should we be lookin for to fix this


lots of air in line? Try gravity bleed one at a time starting with RR--wide open 'til it drips, then LR, then RF, and LF.

Sep 05, 2010 | 1989 Dodge Daytona

2 Answers

How and where do I add power steering fuild to a 1989 Brougham? Can't find the dip stick for the steering fuild and don;t kn ow when I should add the fuild. Can you help?


You add fluid at the P/S reservoir which is belt driven. There is a large cap on top. Remove the cap and there is a built in dip stick. Unless you have a leak you will never have to add fluid.

May 18, 2010 | 1989 Cadillac Brougham

1 Answer

Need illustrated instructions to remove the power steering pump and pulley from a 1989 Chevrolet silverado 4x4 pickup


You will need a pspecial puller and installer to remove and reinstall pulley,My local advanced auto parts store rents these tools.

Aug 25, 2009 | 1983 Chevrolet Silverado

1 Answer

2000 chevy 1500 silverado- rear brakes overheating


Have someone push & release pedal while at wheel with problem. See if it takes a while or slow to release. If yes, have wrench ready on bleeder screw, and try again, if it sticks/holds, crack bleeder screw, if it releases, I'd replace hose.

Jan 18, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Power steering - 1989 toyota celica


looking at the engine from the front of the car the power steering fluid is located on the left hand side and has a black plastic screw-cap about 3inches in diameter open that and pour in fluid. be sure to watch the level markers on the side so you dont overfill. also if you need to keep topping up powersteering fluid you have a leak and should get it fixed asap.

Sep 28, 2008 | 1989 Toyota Celica Liftback

Not finding what you are looking for?
Cars & Trucks Logo

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...