Question about 1993 Jeep Cherokee Country

1 Answer

Stering pump ? for 1993 jeep cherokee 4.0 .

I need help ? how to install a power stering pump with a diagram please?

thank you
rudy

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 242 Answers

Loosen 2 pivot bolts on back of pump, 13mm. then loose one bolt on bottom/front. Turn adjustment bolt on right side/bottom of pump to loosen belt. Once belt if off, remove all of the bolts connection pump to engine bracket. Remove hoses going to pump. Install new one, filled up with fluid. Now you have to bleed air out of sys. Move steering wheel left/right to the stops. Do this about 10 times either direction.

Posted on Sep 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 jeep cherokee horn wont work


Hi there:
Go to the horn under your hood, check it for any thing wrong, then follow the power wire and follow it back to your steering wheal. this is where your problem is you just have to find out where the short is.



If you need other details, I could send a email with the Electrical Section Wiring Diagrams (7 Mb).


Hope helps.

Nov 22, 2012 | 1993 Jeep Grand Cherokee

1 Answer

Can i replace the power steering reservoir in my 1993 grand cherokee?


Hi Riley:
Nice car, I have the same '93 5.2L V8, according with the Jeep Repair Manual for 1993 at 1998, check this procedure to RESERVOIR REPLACEMENT - REMOVAL
(1) Remove power steering pump. Refer to Pump Replacement in this section.
(2) Clean exterior of pump with solvent.
(3) Clamp the pump body in a soft jaw vice.
(4) Pry up tab and slide the retaining clip off (Fig. 7).
(5) Remove fluid reservoir from pump body. Remove and discard O-ring seal (Fig. 8).

11_25_2011_2_41_35_am.gif


11_25_2011_2_42_53_am.gif


INSTALLATION
(1) Lubricate new O-ring Seal with Mopar Power Steering Fluid or equivalent.
(2) Install O-ring seal in housing.
(3) Install reservoir onto housing.
(4) Slide and tap in reservoir retainer clips until tab locks to housing.
(5) Install power steering pump. Refer to Pump Replacement in this section.

If you need other additional details or some specific section from the Repair Manual, feel free to contact us in the previous links.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 25, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Need firing order diagram for 1993 jeep cherokee


Hi Linda:
Try to check the links Grand Cherokee Repair Manual or look under firing order diagram.

Hope this clues helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 19, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Need a pulley diagram for a 1993 jeep cherokee


Try your local dealer PARTS Department...
Best regards
Ck

Nov 15, 2011 | 1993 Jeep Cherokee Country

1 Answer

I need a power stering pump. where's the best place to find a good rebuilt one


napa auto parts or you can go to www.car-part.com punch in your vehicle info and your zip code it will tell you the nearest available part is how much phone # of who has it and how far from your zip code hope this helps

Aug 25, 2010 | 1993 Jeep Cherokee Country

1 Answer

I changed fuel pump and fuel filter truck started an ran. I turned it off an on 4 times to make sure it would run, it did. I put it back together and now it starts but won't stay running? Please help,...


Replace the oxygen sensor. Worked for me! My 1993 Jeep Grand Cherokee was doing this same thing, even after replacing the battery, crankshaft sensor, computer, ignition coil, wires and plugs and fixing vacuum leaks.

Aug 22, 2010 | 1993 Jeep Grand Cherokee

1 Answer

I need a fuel pump wiring diagram for a 1993 Jeep Cherokee


I don't have an isolated diagram but if you go to this link you can have the entire schematic!
http://www.scribd.com/doc/18999822/Jeep-Wiring-2
Get out your glasses and have fun!!!

Jan 17, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Fuse diagram for 1993 jeep cherokee the power seats stopped working trying to figure out what fuse needs to be replaced


In the Fuse Block, Cavity 5, is a Fuse 30A c/BRK

In this document you can find all about the Power Seats:
- 93ZJ-Secc-8R-Power-Seats
- 93ZJ-Secc-8W-Wiring-Diagrams

Good luck (rated this help).

Sep 01, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Need fuse diagram for 1994 grand cherokee.


I have an 1993, and this info is same; check this info:
- ZJ-Secc-8W-Wiring-Diagrams

Good luck.

May 07, 2009 | 1993 Jeep Grand Cherokee

1 Answer

How do i loosen the surpintine belt


Since you did not specify engine size and a/c or no a/c...

CLICK HERE

For the belt diagrams for all 4 options.

If you dont have the 4.0 (auto belt tensioner) you have to tension using the power steering pump pulley.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Mar 29, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Cherokee Country Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...