Question about 1995 Jeep Grand Cherokee

1 Answer

The engine do not work

I have a 95 cherokee, the engine don´t work again after starting it.
one small red lamp is flashing when the car ocasionaly works for almost 5 minutes. the scanner takes cod 12 (memory to controller has been clared within 50-100 engin starts. what i have to do

Posted by on

  • yadayada
    yadayada May 11, 2010

    What does the lamp indicate, oil pressure, what? let me know and I will try and help, thnaks

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Hello primeiro, does your Jeep stay running(5min) or does it start and then dies, like it is not getting enough gas? What is the small red lamp that is flashing? Mine is my security alarm indicater. What do u mean by scanner? and takes cod 12? cod? 12? Let me know what you have tried or what else may have been going on in past but seemed to have stop, for un- reason. Jeeps can be puzzling, and then be fine. Everytime it would act up I would call the Jeep people and schedule a appt. in a day or so, it would keep acting up and then when I drive onto the Jeep people lot it would not act up. AT ALL. I was told there are other Jeep owners that sweared something was wrong but when taken to be check it would be fine. The Jeep people say that I am not the first to feel dumb or I was delusional. So now instead of calling, I go directly there when I had a problem or noise and I had them jump in for a ride to see what I was experiencing. "It's a Jeep thing, you wouldn't understand." I now have on my Jeep on my back window. I LOVE my Jeep,even though they can drive us crazy. Good Luck and Happy Jeepin'

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cherokee 2012 engine does not start


where to start... see if lights turn on, if not charge battery, once battery is charge try again, if cranks then could be battery or alternator, if not could be starter, spark plugs, coilpack... after youve looked at that let me know, ill adv further.

Jul 02, 2016 | 2012 Jeep Grand Cherokee

1 Answer

PERMANENTLY DISABLING ANTI THEFT ON 1995 JEEP CHEROKEE


see this link
what makes you think its (anti theft)??
all jeeps made with Immobilizer, (VTSS/VTA its called then)
the cluster has lamp that tells you VTSS has imobilized the engine (cuts fuel)
if the immo lamp is on, then see below.
93 was first year, click hack 93-98
http://jeepdied.com/
if not glowing that immo lamp
that means its just a no start.

cranks but will not start has over 50 causes.
covered on same page but is called no start.

ZJ 1995

this is the VTA page 8q in the fsm
The Vehicle Theft Alarm (VTA) system is an available
option on Grand Cherokee models. This system
is designed to protect against vehicle theft by monitoring
vehicle doors, hood, liftgate and ignition action
for unauthorized operation. When unauthorized operation
is detected, the VTA system responds by sounding
the horn, flashing the headlamps, park and tail
lamps and providing an engine no-run feature. Following
are general descriptions of the features of the
VTA system. Refer to Group 8W - Wiring Diagrams
for complete circuit descriptions and diagrams

see that lamp below, this tells you what's up.

26166726-iznfychya1k5sjkhauts20c0-4-0.jpg the lamp glows key on to tell you Im alive and that im ok booting up. but then goes out to start car.
does it?

Apr 17, 2016 | 1995 Jeep Grand Cherokee

3 Answers

Need to find a diagnostic code for my 2001 jeep grand cherokee


Service engine soon lamp and check engine lamp have a 16 pin connector under dash in drivers area most parts store can retrieve codes for you for free these codes are in several forms P series are powertrain codes (engine,transmission) B series codes are Body codes ( A/C,electrical windows mirrors) C series are Chassis codes (abs,transfer case, air ride) U series codes are Communication codes between all modules that need to share information..

Oct 04, 2014 | 2001 Jeep Grand Cherokee

1 Answer

Gauges top working security system not working vehicle will start but only runs 2 seconds


fuses, check all fuses in all fuse boxes. under dash and hood.
the IMMO SKIM , stops fueling of the engine.
the SKIM lamp in the dash shows, that. it sticks on or flashes
you have a transponder key ,right?
and you insert the key as the oper guide states, and the lamp SKIM
self tests. then must go out, if not, the engine will never run more than 2 seconds by Design.
  1. so fix the dead dash first.
  2. then get the SKIM lamp out
  3. then start car.

Sentry Key Immobilizer module.

Mar 15, 2014 | 1999 Jeep Grand Cherokee

1 Answer

I have a 95 jeep grand cherokee and the lo beams dont work. highbeams are fine, replaced lights, switch is working, and all fuses are fine. is there anything else i should check?


There may be a lamp outage module, and you may have low and high beam relays in one of the fuse boxes in the engine compartment.
Check your owners manual if you have one.

Jun 22, 2012 | 1995 Jeep Cherokee

1 Answer

I HAVE 95 JEEP GRAND CHEROKEE. AFTER DRIVING CAR FOR SHORT DISTANCE WILL NOT START. LET SET COUPLE HOURS IT WILL START. MAY GO 5OR 6 DAYS NO PROBLEM THEN AGAIN WILL NOT START. HAD TWO GUY CHECK IT wE...


Had similar problem with 96 Jeep 4.0L engine. Tracked it down to the connector for the distributor pickup. Spliced in another connector and hasn't stalled since. Also, have you had any codes? Easy way to check on Chrysler products: turn key on, off, on, off, on (not starting) and watch the 'engine light' on the dash. It will flash off/on. Count the flashes with short pauses between and longer pauses between code. When you get a 5 count and 5 count, that is the end. This may also help

Aug 10, 2009 | 1995 Jeep Grand Cherokee

1 Answer

95 jeep cherokee it wont stay running at red lights


Try a tank of supreme gas, plus a can of SEAFOAM in the gas tank.After running about a half of this tank out. Pull positive post off the battery for about 1-minute. This will reset computer, and it might clean up the fuel problems that you are having. If it keeps on, change the O2-sensor out and do the above steps again.

Feb 12, 2009 | 1995 Jeep Grand Cherokee

1 Answer

95 Grand Cherokee center column data screen resets after shut off


I had the same problem with my 1995 grand cherokee. I had to remove the message center and resolder the connections where the plugs go into the back of it. Not hard to do if you are used to soldering small connections, if not, take it out and bring it to someone who is, like a tv repair shop.

Jan 26, 2009 | 1995 Jeep Grand Cherokee

2 Answers

95 jeep cherokee not starting


Check the small wire on the starter to see if you are getting 12v there with the key turned. If you are, then it is possible that the starter (&or solenoid) that checked out good last year is not good now. If no power at small wire, then check neutral safety switch.

Jan 08, 2009 | 1995 Jeep Cherokee 2 Door

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...