Question about Mitsubishi 3000GT

1 Answer

Ineed to chsnge plugs,can you detail the method in pics for me. thank you

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 60,792 Answers

Here is a picture the wrench is on the plugIneed to chsnge plugs,can you - sparkplugs.jpgof the wrench being used to pull the plug.

Posted on Aug 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ineed exploded veiw of front suspension for nissan


You can find a detailed view of front suspension of Nissan Skyline R32 at this link: Nissan Skyline R32 Front suspension
6_8_2016_5_48_01_pm.jpg

Sep 16, 2013 | Cars & Trucks

1 Answer

97 lincoln mark viii oil pressure light always on. oil pressure good. new sender


test the faulty lamp , turn on the ignition switch to the START position The providing circuit shoudl ligh the warning lamp. If hte light does not come ON during the porve/out, disconnect the sender switch lead. Use a jumper wire to connect the sender switch lead to ground . With the ignition in the RUN position, the warning lamp shoud light. If the lamp is iluminated, replace the sending swith. If the light does not come on, either the bubl is buned out or the wiring is damaged.
God bless you

Sep 28, 2012 | Cars & Trucks

1 Answer

Where are the spark plugs located?


where are spark plugs located on a 2002 Chevy Tracker 4 cylinder

Apr 12, 2012 | 2002 Chevrolet Tracker

1 Answer

Ineed the torqu specs on a 1998 gmc jimmy 4.3litet for the rod and main bearing and oil pump bolts


Hello rdt452428,

For the bearing cap bolts there are two methods.
The preferred method is two steps:

Step one, torque cap bolts to 15 ft.lbs.
Step tow tighten an additional 73 degrees.

The optional method is to torque all cap bolts to 77 ft.lbs.

For the connecting rod nuts its a two step process:

Step one, torque nuts to 20 ft.lbs.
Step two, tighten an additional 70 degrees.

The oil pump to the rear crankshaft bearing cap is torqued to 66 ft.lbs.

I hope this help.

Regards,

netvan

Jul 21, 2011 | 1998 Chevrolet Suburban

1 Answer

Ineed the spark plug firing order for 1992 ford 3.0


1992 Ford Ranger 4WD 3.0 liter V-6 VIN "U"

2ed03fb.gif


Hope helps with this (remember comment and rated this).

Jul 17, 2010 | 1992 Ford Ranger

1 Answer

HEATER FAN CONTROL DOWN TO 2 SPEEDS


The control is not the problem. Your blower motor resistor is burnt out on two fan speeds.
This is a high failure rate item that the factory has redesigned at least twice for this concern.

Feb 24, 2010 | 1999 Chevrolet Venture

1 Answer

Tune up itakeof my wires and itry to fix and after i turn on car ifind my car ghaking and ineed mycar to go to work ineed help pless


Did u change the spark plug wires or just take them off and put them back on? How did the car run before u did this? What engine and mileage? Is it possible u put the wires back on in the wrong order (this would make it shake, and run poorly).

Oct 19, 2008 | 1998 Volvo S70

1 Answer

Radio


check your log books for details if not your dealership should be able to provide this information

May 25, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...