Question about 1997 Cadillac Seville

1 Answer

Brake peadl goes to the floor - 1997 Cadillac Seville

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Leaking brake caliper or a leak in the brake line

Posted on Apr 08, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No resistance on my brake peadle for my 2002 ford taraus


If you have a pedal that drops to the floor you have serious issue and should have it looked at professionally ASAP, if you are not mechanically inclined, and you do something wrong you could seriously hurt or kill someone. my son has perminent injury due to someone with faulty brakes.

Apr 04, 2014 | 2002 Ford Taurus

1 Answer

How to bleed the brakes


Start at the right rear wheel, while having someone in the driver seat, have them to apply pressure to brake peadle while you open the bleeder valve located at the top of the caliper. After fluid stops coming out of the bleeder valve close valve, and person in the driver seat can release pressure off of brake peadle. perform this till all air is out at each caliper. Right rear first, then left rear, right front, and then left front, be sure to check brake fluid level after each caliper is bleed.

Jun 20, 2012 | 1996 Dodge Caravan

1 Answer

Brake lights stay on in my 94 Acura TL 2.5


your sinsore on or behind the brake peadle might be stuck

May 31, 2012 | Cars & Trucks

1 Answer

Clutch peadle is stuck to the floor


CLUTCH TO THE FLOOR, YOU COULD HAVE BROKEN RELEASE BEARING OR FORK,COULD HAVE BROKEN OR DISCONNECTED CLUTCH CABLE.

Jul 07, 2011 | 2004 Chevrolet Cavalier

1 Answer

Brakes are real spongy and we changed the master cylender, and bled them but still spongy, the peadle is nice and hard when not running but as soon as u start it peadle goes right to the floor? i dont...


hi.

it sounds like there is still some air in the brake system.

when the engine is not running the brake servo is not working either. when you start the engine, the servo works as well, putting far more pressure on the brakes.

bleed the system again, starting at the cylinder furthest from the master working to the nearest.
if this does not improve the brakes then try bleeding the system again, but with the engine running to activate the servo system. this should expel any remaining air.
BE CAREFUL doing this. always put safety first. try to use axle stands to lift the drive wheels if possible.

May 25, 2011 | 2005 Isuzu Vehicross

1 Answer

Dont know how to replace brake light switck


Remove the cover from under the dash and look up above the brake peadle about 5 inches you should be able to see the switch there may be 2 switches if you have cruse contronl. The brake light switch should have white and orange wires. just pull back on the switch to remove it. When putting the new one in push the brake peadle in then push the switch all the way in the hole then pull the brake peadle back till it stops this will push the switch back out some this will adjust the switch. Of course ckeck for proper operation. Here is a bad diagram of the switches but it the only one I could find.547561f.png

Oct 20, 2010 | 2000 Buick Century

1 Answer

Brake peadle goes soft at slow speed or when bakking up. Replaced the following, master cylinder. vac pump, complete front and rear brakes. booster.


Sounds like there is air in the brake lines. did you bleed the fluid until it came out clear? Not foamy color.

May 11, 2010 | 1997 Ford F350 Crew Cab

2 Answers

Break peadle wont hold pressure


U are going to need a new brake master cylinder, the internal seals are leaking and allowing the fluid pressure to leak down, this why the sinking pedal

Jan 10, 2010 | 1994 Ford Crown Victoria

1 Answer

Rear brake job


pull the two bolts holding the caliper on and pull the caliper off now get a C clamp and compress the piston all the way into the caliper now remove the two bolts in the caliper hanger and remove the hanger now the caliper should just pull off ( if corroted hit it with a hammer ) now just put every thing back to gether the way they came off...............WHEN DONE WITH THE BRAKE JOB MAKE SURE TO START THE TRUCK AND PUMP THE BRAKES UNTIL THE PEADLE IS HARD. YOUR PEADLE WILL GO RUTE TO THE FLOOR AT LEAST ONE TIME MAYBE MORE.

Jan 06, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Peadle goes to the floor with no pressure behind the pedel fluid


you will need to replace your master cyl and bleed your brakes
your master cyl is bypassing inside or the seal are bad inside the master cyl
there isnothing slse in the system that could cause this unless you are loosing fluid.
good luck

Nov 11, 2008 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
1997 Cadillac Seville Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...