Question about Ford Crown Victoria

Open Question

1998 crown victoria - i cleaned the fuel injectors on the passenger side. hooked everything back up and went to start the car. the car ran really rough. i shut the car off and tried to re-start. the car made a poof sound and then nothing, no dash lights, no bells, nothing. there was a puddle of gas that came from near the back of the engine. the car sat for a while and i went back to tryand start the car, i had dash lights and bells. i tried to start the car and the same thing happened, the poof sound and nothing. please HELP!!!

Posted by on

  • Jeff Turcotte
    Jeff Turcotte Apr 08, 2011

    check to see exactly where the gas is leaking from.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 261 Answers

SOURCE: 2000 Ford Crown Victoria

when you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Posted on Nov 24, 2008

Ad
dr_layinlow
  • 60 Answers

SOURCE: engine shuts off while driving

check one of your coolant sensor's

Posted on Dec 07, 2008

  • 1118 Answers

SOURCE: engine turns over fine , car will not start.

well the first part of your question i was all ready to tell you to put a new fuel pump in, now not so sure, there is a relay for fuel pump, can you hear pump cycle and relay click? relay under hood you will have to listen close they don't run long maybe a couple secounds, if you don't relay bad. if you do pump could be bad, do fuel pressure test pump could be weak. don't think sunroof and turn signals are related, but stranger things have happend.

Posted on Jan 25, 2009

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 crown victoria wont stay running


sounds like a fuel problem to me ..... maybe the fuel filter is clogged or the injectors need cleaning

Mar 09, 2013 | 1997 Ford Crown Victoria

1 Answer

I have an 2000 ford crown victoria interceptor that was showing a po301 misfire after I had installed a new cop the night before. So I decided to switch the cylinder one cop and plug to cylinder two and...


Absolutely. But check connections first. Also, did it come with a new boot. If not replace it. Do your swap test again, and you'll know for sure.

Oct 22, 2011 | 2000 Ford Crown Victoria

2 Answers

Need to know the cylinder numbers on a ford crownvictoria 1998 police pakage


1 2 3 4 on the passenger side front to rear 5 6 7 8 on drivers side front to rear

Feb 14, 2010 | 1998 Ford Crown Victoria

1 Answer

Gas not getting engine(flter or pump)


Sounds like the fuel pump and filter. Spray starting fluid in throttle body if cars starts the its your fuel pump and fuel filter.

Oct 29, 2009 | 1998 Ford Crown Victoria

2 Answers

Can a fuel pump be accessed through the back seats on a 1993 Crown Vic?


what does a crown victoria look like?? none here in spain ,focus yes ,but knowing ford it uses the same parts so try lifting the back seat up and look for a big round plastic cover.My jaguar has ford name on a lot of components behinfçd the dash

Oct 23, 2009 | 1999 Ford Crown Victoria

1 Answer

1985 crown victoria stalls out


Why not hook a fuel pressure gauge up to it & see what the pressure is ?? Am I missing something here?

Aug 31, 2009 | 1985 Ford Crown Victoria

1 Answer

How are the cylinders numbered on a 1998 ford crown victoria with a police package


Firing order is 1-3-7-2-6-5-4-8 Passenger side of engine starting at front and going back is 1-2-3-4 Driver's side starting at front going back is 5-6-7-8.

Jul 06, 2009 | 1998 Ford Crown Victoria

1 Answer

How do I find the fuse for 1987 crown victoria fuel pump?


under driver side of dash.there may possibly be one under hood in fuse panel.why are looking for the fuel pump fuse???also there should be a fuel pump kill switch on passenger side floor kick pannel to the right of passengers foot behind plastic or in trunk..hope this done you some good....

Jul 05, 2009 | 1987 Ford Crown Victoria

1 Answer

2000 ford crown victoria


hello lipounds , the temp sensor located on the passenger side front of engine near the #1 injector . hope that fix ya .

Jan 02, 2009 | 2000 Ford Crown Victoria

2 Answers

2000 Ford Crown Victoria


when you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Nov 24, 2008 | 2000 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...