Question about Honda Accord

1 Answer

Cant seem to get it to fit right not sure if I am installing it properly seems too loose?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

Need more info. Not sure what you are installing on to what. Please repost with more info.

Posted on Apr 07, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine belt fitting loose I cant seem to find the problem y?


sounds like perhaps the tension er pulley has a problem .they should never be loose

Jul 28, 2015 | Cars & Trucks

2 Answers

1991 toyota camry battery draining


when you say it won't start or it won't turn over ?????

Mar 13, 2014 | 1991 Toyota Camry

1 Answer

I have a 83 plymouth reliant i have replace everything but the carb it seem to stop and go right when i hit about 35 and again when i hit 65 i cleaned the carb out still seems to do it put new fuel filter...


check for vacume leaks first. you stated that the carb was loose and you tightened it. you probably need to replace the gasket beneath it (thats why the carb seemed loose)

Feb 09, 2014 | 1983 Plymouth Reliant

2 Answers

HEALIGHT NOT ALIGNED WITH THE Other one?


There are two torqs style alignment screws, one for up/down the other for left/right. These screws can be found next to the headlight. Before adjusting the screws check to see if both headlights have similar play when you move them by hand. I had a sliding lock tab out of place, so one headlight seemed loose and hard to adjust. If one headlight is loose, look for two plastic 'sticks' (1" wide) directly behind the light. These 'sticks' are slotted to fit over one fixed metal rivet and one plastic tab from the headlight. The trick is making sure the bottom of the stick fits in a pocket below the light. It's best to use a flashlight and a long flat-blade screwdriver to push the stick into the pocket as it locks over the tabs. Without all three points of contact the headlight will seem loose.

Apr 03, 2010 | 2002 Chevrolet Blazer

1 Answer

Horn only works some time === right rear taillight same thing.


Hello Sir

It seem that you are facing some loose connection problems. Do check the following possibilities:

Make sure that all the fuses and relays are properly installed and intact. (Fuse box is located under the hood or underneath the steering wheel room).

Make sure that the positive terminal of the battery is properly installed and didnt have any carbon.

The connections to the horn and tail light are properly connected. (There might be some loose connections).

If all of these techniques does'nt works, you need to change the horn relay or the horn.

Regards,
Waqar.

Nov 15, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

My car trembles when i accelerate and when its on


wiggling or trembling are mostly cause by the front wheels.
it could only be unbalanced air pressure of the tires.
if not, it could be loose tie rod ends connecting to the steering wheel. fittings might have been worn out already and needs to be replaced.
to check whether if which side is causing it, lift or jack the left or right tire, then manually try to wiggle it, push or pull it, try every possible way to determine and looseness on the wheel. do the same on the other front wheel.
if one of then is loose or wiggles as you check, then there is a loose part on that wheel. check carefully.

May 29, 2009 | 2000 Lincoln Town Car

1 Answer

Passenger door lock removal


hello,seems you have a sticky siding maybe because of plastic clips,try to insert a plastic wedge siding and door,pull the lower part and lift a bit,observe the movement of siding,how about the screw in lower armrest,press off the cover,then look for screw,be sure no screw are fitted,ty

May 02, 2009 | 1996 Mercedes-Benz C-Class

1 Answer

Cant get positive terminal off its post


Buy a battery cable remover. It lookc like a clamp. The hooks go under the cable end and the post goes to the center of the terminal. When you turn it, the terminal will pop right off. About $5.

Mar 21, 2009 | 2003 Hyundai Tiburon

1 Answer

New rotor seems too loose


if it works use it. if it doesnt they gave you the wrong one, if it look like it will contact the points on the cap ok then try it.

Mar 19, 2009 | 1983 Ford Ranger

1 Answer

Brake light switch 88 jeep wrangler


bend the bracket that the switch mounts to back so you can tighten the nut all they way and adjust the switch properly, otherwise there may be a stopper bolt thru the pedal bracket that adjusts the travel of the pedal good luck and please rate -jeff

Jul 02, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...