Question about 2005 Nissan Murano

2 Answers

Nissan Murano 2005 SL keyless entry remote programing, got a used remote, how can I program it?

Posted by on

  • 9 more comments 
  • buick04 Aug 21, 2008

    how do I program the remote and the chipped key for a 2004 Buick Lesabre?

    thanks!

  • Anonymous Sep 03, 2008

    INTEL. KEY IN MY 2005 MURANO WENT THRU WASHING MACHINE AND NOW DOES NOT WORK, ANY IDEAS OF WHAT I CAN DO. tHX. BILL

  • robertrwt Sep 03, 2008

    I have a 2005 murano SE it has the keyless entry and starting. My problem is that the keyless remote has a hard time unlocking the doors and i put new batteries and still have the same problems i even sometimes have to take the key out of the keyless remote and open the door with the key. Any solutions RWT thanks

  • Anonymous Mar 16, 2014

    2008 Nissan Sentra used to have good range with remote, now only about 10 feet. Replaced batteries and tried other remotes, no improvement.

  • Anonymous Mar 17, 2014

    Neither keyless remote

  • Anonymous Mar 17, 2014

    dodge durango keyless entry 2005

  • Anonymous Mar 26, 2014

    what does the motor mount sensor do

  • Anonymous Mar 26, 2014

    what does the motor mount sensor do

  • Anonymous Mar 28, 2014

    2004 Nissan murano phone charger does not work

  • Anonymous Mar 30, 2014

    Heat will not blow warm air

  • Anonymous Mar 30, 2014

    how do you program a new remote

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 643 Answers

If you have a seperate Key and Remote use the procedure below.
If you have a Remote Key Combo (Remote in the head of your key). There is no manual way to program keyless remotes to this vehicle. Please contact a Locksmith or your local dealership to get a quote on how much it will cost to program keyless remotes to this vehicle.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
1. Close and lock all doors with the driver's side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver's side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver's side power lock/unlock switch and open the driver side door.



Posted on Oct 18, 2012

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't get the Viper remote starter to start my Nissan Murano it worked fine and now it just beeps


presuming that you have replaced the batteries in the remote, check to see if someone may have tampered with your installation

May 03, 2015 | 2009 Nissan Murano SL

1 Answer

Where is the airbag module located on my 2005 nissan murano. is it in the steering column?


There is no module for air bags .
There is a fuse its not something that needs sensors unless their is an impact witch their are sensors for but not a signal module. because its a federial mandate and their several impact points on vehclies.

Mar 07, 2015 | 2005 Nissan Murano SL

1 Answer

Removing the front power outlet on a 2007 Nissan Murano?


location of airbag ECU on 2001 (Y) peugeot boxer 2.8HDI

Jan 20, 2014 | 2007 Nissan Murano SL

1 Answer

KEYLESS ENTRY REMOTE IS NOT WORKING AFTER CHANGE OF BATTERY


You will have to re initialize it or have it programmed.

Dec 06, 2009 | 2005 Nissan Murano

1 Answer

Keyless Entry Programming Nissan Murano 2005


are the batteries in correctly and is the button in good working order

Aug 21, 2009 | 2005 Nissan Murano

1 Answer

2005 nissan murano sl, with rattling sound when accelerating


I recently experienced the same symptom with my '05 Murano and it was not a fuel problem. The dealer listed the cause as dry axle splines and replaced both front drive shaft assy's. Note that this was done as warranty with no cost incurred by me.

Jun 05, 2009 | 2005 Nissan Murano

1 Answer

Replacing the rear parking light


Remove the finisher panel - its a long black plastic cover on the light housing - (pop it off) from the inner edge of the taillight, remove the screws.

Dec 01, 2008 | 2005 Nissan Murano

1 Answer

Nissan Murano 2005 SL keyless entry remote programing, got a used remote


have you tryed and reprogram it? if you have the fault lies in the the system and you need to replace it because it is a factory error.

Sep 05, 2008 | 2005 Nissan Murano

Not finding what you are looking for?
2005 Nissan Murano Logo

3,468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...