Question about 2000 Oldsmobile Intrigue

1 Answer

Cannot close sunroof. Clicks in open position (electrical).

Posted by on

  • vikgenlib Apr 10, 2011

    Yes sort of but it turns out that I have to take the car to a shop to have the headliner removed for a solution as no one can tell without doing so.
    Thanks for your help.
    Richard

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

The sound you might be hearing is the relay or the switch or the motor itself. It may be a bad relay or bad wiring. The relay for your sunroof should be in the center underneath the dash or at the passenger side depending on who installed and year of the car. It may also be an issue with the motor. The motor is located on top. It is usually at the car's front 'ceiling' towards the rear viewmirror. Check if there is motor sound or clicking or vibration on top. The motor may be week or may have gone out of alignment. You will have to remove the upholstery on top to get to it.

Posted on Apr 07, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wifes sunroof is open and will not close. Checked fuse it has pwr, removed switch it does not have power ... a ground problem at the sunroof motor...where is that?


First off this is controlled by a module (computer) The switch would only have five volts . 5volt reference voltage from the control module . Not knowing how to test the electrical circuit's for this could be expensive . Short out the module or 5 volt ref. voltage circuit inside the module.
Your best bet , take it to a qualified repair shop . Look at a wiring diagram here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine size . Under system click on body & accessories ,then under subsystem click sun roof . Then click search button then the blue link . Now tell me you under stand what's happening here .

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof Opening Position Switch (SOPS)
• Sunroof switch
• Sunroof motor/actuator
• Sunroof glass (spoiler type, with glass sliding above roof)
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power supply for the sunroof control module: SUNROOF 20 A fuse
• Ground from G302

Sunroof Opening Position Switch (SOPS)
The SOPS tracks the position of the glass through 2 limit switches:
• Soft stop limit
• Vent limit
The sunroof control module monitors the limit switches and based on the inputs determines the position of the sunroof glass. As a limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling down the 5 volt reference to 0 volts.
The sunroof control module understands the position of the sunroof glass based on the different input combinations through the sunroof limit switch soft stop signal and sunroof limit switch open vent signal circuits.

Power Sunroof Does Not Close
Perform the Initialization/Teach Process any time a new sunroof motor actuator is installed in the vehicle or any time an existing sunroof motor actuator is removed from the vehicle. Refer to Sunroof Motor/Actuator Initialization/Teach Process .

Oct 23, 2017 | Pontiac Cars & Trucks

1 Answer

Sunroof does not open. Fuse is ok and the shade operates normally.


Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

Feb 10, 2017 | 2010 Buick LaCrosse CXS

1 Answer

2001 cadillac deville sunroof open and want close


Check the RAP fuse in the rear fuse box , this fuse powers the sunroof control module ! Fuse Block - Rear , Left rear of the passenger compartment, under the rear seat .
The sunroof module contains the logic for the opening and the closing of the sunroof. The sunroof motor assembly contains the reversible DC drive motor, the gear train, and the limit switch.
The sunroof module determines the sunroof motor direction based on inputs received from the overhead console sunroof switches. When the ignition switch is in the ON position or when retained accessory power (RAP) is active, voltage is applied to the sunroof module via the RAP relay. For a description and operation of the RAP system, refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power. The sunroof module controls the sunroof motor direction by changing the polarity of the applied voltage. The sunroof module remembers the sunroof position whenever the ignition switch is turned to the OFF position. The limit switch is used as an input to the sunroof module to indicate that the glass is fully closed, or in the comfort stop positions. The limit switch is grounded when the sunroof glass is in the fully closed or comfort stop positions, otherwise it is open.
The SLIDE CLOSE mode is initiated by moving and holding the sunroof slide switch (ROOF) forward. This applies a ground provided from the sunroof limit switch low reference circuit to the sunroof switch close vent signal input of the sunroof module. The sunroof module controls voltage to the control circuits of the sunroof motor. The sunroof motor will run until the limit switch contacts are closed. The closing of the limit switch will apply the sunroof limit switch low reference circuit to the sunroof limit switch soft stop signal circuit to the sunroof module, indicating the flush closed position has been reached. As the sunroof is approaching the close position the sunroof glass will force the wind deflector downward.
You need to have a factory scan tool hooked up an have it checked for DTC'S in the sunroof control module ! a code reader will not do this , a code reader will only check the engine codes for OBD 2 .
Important: The following must be completed before using the symptom tables.
  1. Perform Diagnostic System Check - Power Sunroof in order to verify that all of the following are true:
  2. ?€¢
    No DTCs are set.


    ?€¢
    The control modules can communicate via the serial data link.

  3. Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation
your better off taking to the dealer !

May 09, 2015 | 2001 Cadillac DeVille

1 Answer

My Pontiac G6 Sunroof is stuck in the vent position.


might try spraying white lithium grease on the slides and open and close few times my g6 did the same thing grease it and open and closed a few times then it work

Feb 28, 2015 | 2006 Pontiac G6 GTP

1 Answer

Stuck sunroof


This is an electrical problem. Check fuses and replace if necessary.

Jul 05, 2013 | Cars & Trucks

4 Answers

Electric sunroof stuck open can it be closed manually


THE ELECTRIC DRIVE SYSTEM FOR POWER SUNROOF IS NOT ADJUSTABLE.DONT REMOVE THE SUNROOF MOTOR UNLESS THE SUNROOF IS COMPLETELY CLOSED.OTHERWISE A NEW MOTOR WILL HAVE TO BE INSTALLED AND TIMED WITH A TOOL THAT COMES WITH THE NEW MOTOR.THE GLASS PANEL CAN BE ADJUSTED.OPEN THE INTERIOR SUNSHADE ALL THE WAY BACK AND OPERATE THE SUNROOF UNTIL FULLY CLOSED.THERE ARE THREE GLASS MOUNTING SCREWS ON EACH SIDE OF THE SUNROOF OPENING.INSIDE THE VECHICLE LOOSEN THE SCREWS SET THE FRONT EDGE OF THE GLASS TO BE JUST 1MM BELOW THE SURFACE OF THE ROOF.ADJUST THE GLASS AT THE REAR EDGE TO BE JUST ABOVE 1MM THE ROOF AT THE REAR TIGHTEN THE SCREWS.

May 23, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Moonroof wont close all the way


Do you know how to test automotive electrical circuit's with a DVOM - digital volt ohm meter ? When adjusting the moon roof did you see any switches ? sunroof limit switch
Measure the reference voltage of the sunroof limit switch soft stop signal circuit at the sunroof control harness connector to a good ground.
Does the reference voltage measure near the specified value?
4.5-5.5 V
Notice: Do not open the sunroof glass past the full open soft stop position. Doing so may damage the sunroof assembly and or the roof top.
Connect a jumper wire to the sunroof limit switch soft stop signal circuit at the sunroof control module harness to a good ground.
Turn ON the ignition, with the engine OFF.
Using the sunroof switch, operate the sunroof system, not to exceed the full open soft stop position.
Does the system operate as requested?

Do you know what a wiring diagram is ? Free one's here
http://www.bbbind.com/free_tsb.html Enter vehicle info. year ,make ,model an engine size . Under system click body & accessories ,then under subsystem click on sun roof . Click the search button then the blue link . See the control module , motor an the two switches ? One is probably miss adjusted . or bad !

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof motor with the limit switches
• Sunroof switch
• Sunroof glass-spoiler type, with glass sliding above roof
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power sunroof system circuit breaker: PWR WDO 25 A
• Ground: G204

Sunroof Limit Switches
The sunroof limit switches track the position of the sunroof glass through two limit switches:
• Soft Stop limit switch through the sunroof limit switch soft stop signal circuit
• Vent Stop limit switch through the sunroof limit switch range signal circuit
The sunroof control module monitors the limit switches and based on the input combinations, determines the position of the sunroof glass. As a sunroof limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling the 5 volt reference to 0 volts.
The sunroof control module monitors both sunroof switch input requests and based on the sunroof limit switch input combinations, will control an output to the sunroof motor, to drive the sunroof glass to the requested position.

Sunroof Motor
The sunroof has a bi-directional motor. When the motor is not operating both circuits are grounded. When the motor drives the sunroof glass in the direction from the closed to vent or vent to open position, the following occurs:
• Voltage is supplied to the sunroof motor open circuit.
• Ground is maintained to the sunroof motor close circuit.
When the motor drives the sunroof in the direction from the open to vent or vent to closed position, the following occurs:
• Voltage is supplied to the sunroof motor close circuit.
• Ground is maintained to the sunroof motor open circuit.
The sunroof control module is equipped with a timer circuit which stops the operation of the sunroof motor after 8 seconds.

Dec 23, 2017 | 2003 Pontiac Sunfire

2 Answers

Sunroof will not close. The sunroof is stuck in the forward open position. The battery died when the roof was left open and now I cannot close the sunroof. I can hear the relay click when I push the...


Can't say for sure about this particular model, but most vehicles with sunroofs have a manual crank for situations like this. Generally it is located forward of the sunroof on the roof of the interior of the car, sometimes under a panel or interior light. This at least will get the roof closed until the problem can be fixed. It may also allow the sun roof to realign itself and help the electric crank to start working again.

Aug 13, 2009 | Cadillac DeVille Cars & Trucks

3 Answers

Volvo V7 '01 sunroof will not stop in closed position


I think I know the answer....your gear has slipped on the cable a few teeth. Set the roof to the desired closed position, flush with your roof. Then open the panel above the mirror by first prying off the switch plate and removing the two 10mm bolts holding the mirror. Remove the sunroof motor gear, or rather just lower it out so it is disengaged with the cables. Now connect the switch and hit the auto open button as if you wanted to open the roof with single flick of the switch. Now hit the auto close button (same button of course, but the single touch method). The motor will advance and stop to where it thinks the roof should be, closed, which it is. Reassemble the gear into the slot, test it if all good, replace the mirror and panel.
Good luck.
Manfred.

May 10, 2009 | 2001 Volvo V70

1 Answer

Chevy Tahoe Sunroof is stuck open moves slightly forward and back


It sounds like it just needs to be reinitialized. Turn your key to the on position with motor off and hold the up/full vent button down for at least 30 seconds or until your sunroof either clicks or goes to the full vent position. That should fix your problem.

Mar 07, 2009 | 2004 Chevrolet Tahoe

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...