Question about 1994 Jeep Wrangler

1 Answer

1994 Jeep Wrangler 4cyl - Bleeding slave cylinder

Help! I am replacing the master/slave cylinder assembly in a '94 Jeep Wrangler. I have located the bleeder screw in the new assembly, however there is no screw! In the old assembly there is an allen screw, should I be using the old screw? Purchased the part from a dealer, called them back with this question and they didn't know!

Any help is greatly appreciated.

Posted by on

  • buyandsellme Sep 09, 2008

    I am also having a huge issue with this cylinder- the new slave cylinder has a bleed hole on the side and not where the bleed screw goes(?) You can not bleed because it is sealed................HELP!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

This is not a bleeder hole, this is a weep hole like in a water pump to see when there is seepage past the seals.

Bench bleed the system. With the master cyl. line and slave cyl assembled, place the master cylinder in a vise, fill the master cyllinder. actuate the slave cylinder back and forth lower than the master cyl. This will allow the air to escape upwards back into and out of the master cyl.
Once bled the system can be installed.

Good Luck

Posted on Oct 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 95 Wrangler YJ 2.5 with a clutch problem


Hi Bruce
I advise you to check the flexible hose first, if its ok, so the problem is the master/slave cylinders.
Good luck

Mar 08, 2014 | 1995 Jeep Wrangler

1 Answer

Looking for a diagram for a 1999 Jeep Wrangler Sahara that shows photos on how to find the bleeder screw on bleeding the clutch


You wont need a photo its super easy, but it is under the jeep follow the line from resivior to the clutch master cylinder (holds fluid) then the other end located on the trannsmission is the slave cylinder the bleeder is on it usually has a rubber cap on it! hope this helps. p.s. dont let the resivoir get empty it will leave air in the system and make bleeding almost impossible.

Aug 17, 2010 | 1999 Jeep Wrangler

3 Answers

!991 Jeep Wrangler clutch pedal loses pressure. I have to pump it to get enough pressure to shift. I keep it full of brake fluid. I can see no leaks. Thanks for any help.


leaky slave or master cylinder - if you have someone listen to the slave cylinder while you press the pedal is should "squelch" if there is air in there, if the slave cylinder doesn't make a squelching sound then the master cylinder or a hydraulic line between the two cylinders is leaking - slave cylinder isn't very expensive but the master cylinder can be rather pricey. and any good parts shop or motor-factor can source or make-up a new hydraulic line if it is the line itself that is leaking.

Jan 27, 2010 | 1991 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

2 Answers

I need to bleed the clutch on my 1992 jeep wrangler and need to know were to locate the bleeder insert


The bleeder valve will be on the slave cylinder. Follow the hydraulic line from the Master Clutch cylinder down to the slave cylinder by the transmission.

Oct 04, 2009 | 1992 Jeep Wrangler

1 Answer

No fluid in clutch resevoir


If you have an internal slave cylinder check it for leaks or if an external slave cylinder check it for leaks. Check the back side of the master cylinder where it attaches to the firewall and see if the seals are leaking. If so replace the master or rebuild it. Same with the slave cylinder.

Aug 15, 2009 | 1994 Jeep Wrangler

4 Answers

1991 jeep wrangler clutch


U have what is called a hydraulic clutch, one of the hydraulic cylinders hs failed, there is a master and a slave cylinder. The most likely and most common cylinder to fail is the slave cylinder, this requires the transmission to be pulled out to replace it. the art is around $125.00, while the trans is out u might as well replace the clutch, the labor is about the same. Here is a picture of the part, let me know if u can see it.



1abd4ec.jpg

May 13, 2009 | 1991 Jeep Wrangler

1 Answer

Clutch still won't come up off of floor after replacing both master and slave cylinder for the clutch on 94 passsat


Try unbolting the slave from the bellhousing, leave the fluid line attached. Bleed the slave, then bolt it back on. Make sure that when you are bleeding it, hold the slave so the bleeder is up.

Apr 17, 2009 | 1994 Volkswagen Passat

2 Answers

Hydraulic clutch for jeep wrangler 2000


hello usaully it is on the slave if not try to hold the clutch pedal in overnight with a stick or something take the cover off the master for the slave so air can escape thru the top goodluck

Sep 18, 2008 | 2000 Jeep Wrangler

Not finding what you are looking for?
1994 Jeep Wrangler Logo

1,072 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...