Question about Chevrolet Tahoe

Open Question

2007 cheverolet tahoe code-0121 throttle position sensor1 performance

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 811 Answers

SOURCE: Throttle/Pedal Position Sensor/Switch B Circuit Range Performance

buy manual, use ohm meter,  adjust tps 

Posted on Sep 13, 2009

Ad
  • 35 Answers

SOURCE: Where is the pedal sensor for a gmc yukon 2007

P0121 Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance Problem
that is a drive by wire system the gas pedal has a sensor rigt above it make sure the plug is all the way in or the sensor could have a glicth in it and would have to be replaced

Posted on Mar 25, 2010

jturcotte
  • 8567 Answers

SOURCE: I have a 2007 Chevy

If it is a code P0226 I would not consider it a safety issue.


Throttle position (TP) sensor C/accelerator pedal

position (APP) sensor ? - range/performance problem


Possible Causes: Accelerator cable adjustment, TP/APP sensor

Throttle position (TP) switch C/accelerator pedal position

(APP) switch ? - range/performance problem
Accelerator cable adjustment, TP/APP switch

This might only be an adjustment issue--make sure the throttle cable isn't so tight that the throttle cannot fully close.
If the cable is OK, it is probably the accelerator position sensor under the pedal.
There are procedures for testing the unit that I will paste below if you care to try them.

If you just want a shop to fix it, the part is about $50 and labor should only be 30 minutes.


Operation The sensor is made up of the two individual sensors within a single housing. Each sensor has a unique functionality to determine pedal position. The APP system along with the Powertrain Control Module (PCM) is used to calculate and control the amount of acceleration and deceleration through fuel injector control.


Removal & Installation

  1. Remove the driver-s side knee bolster.
  2. Push down on the small tab and disengage the electrical connector.
  3. Remove the pedal bolts and remove the pedal and sensor assembly.
  4. Installation is the reverse of removal.

    5bcaece.gif

Fig. APP sensor mounting
Testing

  1. Install a 3 amp fused jumper wire between the 5-volt reference terminal of the APP sensor and 5 volts. Install a jumper wire between the low reference terminal and a ground.
  2. Sweep the sensor through the entire range while monitoring the voltage between the signal terminal and the low reference terminal with a digital multimeter. The voltage should vary between 0.30-4.98 volts without any spikes or dropouts.
  3. If the voltage is not within the specified range or is erratic, replace the accelerator pedal assembly.

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 S-type jaguar that goes into a limp mode and stops running then the engine system fault shows ,the parkbrake fault and DSC not available also shows. Diagnostic showed codes PO121,P1582??


code p 0121 is associated with the throttle position sensor and accelerator position sensor
causes are from cable adjustment --throttle position and accelerator position sensors
code p0533 refers to ac refrigerant pressure sensor--high input== causes --ac pressure too high (cooling fault -condenser fan not running at radiator-- too much gas --pressure sensor
p 0105 refers to map sensor / barometric pressure sensor --circuit malfunction===causes wiring--- map sensor --baro sensor ECM
code p0566 refers to cruise control master switch== causes --control switch , ---ECM
code p1582 refers to electronic throttle monitor data available which will be associated with the p 0121 code and faults

Jan 08, 2017 | Jaguar Cars & Trucks

1 Answer

2000 volvo s80 turbo code p0121


code p 0121 refers to throttle position (TP) sensor A/accelerator pedal position (APP) sensor A--range/ performance problem===causes ---accelerator cable adjustment--TP/APP sensor ---wiring

Dec 23, 2016 | Volvo Cars & Trucks

1 Answer

Dtc p0121 throttle position (tp) sensor performance


code p 0121 has to answers
1--refers to throttle position (TP) sensor/accelerator pedal position sensor A--range /performance problem====causes --accelerator cable adjustment--TP/APP sensor ---wiring
The second reference is the same and the causes are--accelerator cable adjustment--TP/APP switch
(APP is accelerator pedal position)

Aug 30, 2016 | Cars & Trucks

1 Answer

How do you check a throttle position sensor on a 2007 chevr tahoe 4x4


The 07 Tahoe has a fly by wire system so there is two throttle position sensors. One on the throttle body the other is in the gas pedal assembly. Check them with a scanner the voltage should be almost the same voltage.

Feb 01, 2014 | Chevrolet Cars & Trucks

1 Answer

How to fix a 2003 dodge durango trouble code 0121


- Faulty throttle position sensor
- Throttle position sensor harness is open or shorted
- Throttle position sensor circuit poor electrical connection
- Faulty Powertrain Control Module (PCM)

Apr 16, 2013 | 2003 Dodge Durango

1 Answer

I have a 2007 tahoe and it keeps coding off & on / throttle position and i tested the plugin im getting 5 volts on 3 of the ports also the remote start deosn't work when the engine light comes


The 5 volt reference comes from the computer which is normal. The sensor could have a dead spot just off idle, or a problem with the wiring harness back to the computer.
I can't advise on the remote start issue.

Dec 18, 2012 | 2007 Chevrolet Tahoe

1 Answer

P2176 code on Chevrolet Tahoe


check all connections on the throttle body ensuring ur getting power to all sensors as normally, this indicates an issue with the throttle position sensor

Apr 26, 2012 | 2007 Chevrolet Tahoe

2 Answers

I had my throttle body cleaned on my 2007 tahoe now its idling to high why


maybe vaccum leak or your throttle position sensor has been effected

Jan 23, 2011 | 2007 Chevrolet Tahoe

1 Answer

Where is the pedal sensor for a gmc yukon 2007 located p 0121 code


P0121 Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance Problem
that is a drive by wire system the gas pedal has a sensor rigt above it make sure the plug is all the way in or the sensor could have a glicth in it and would have to be replaced

Mar 24, 2010 | 2007 GMC Yukon

1 Answer

P1516 code


CODE P1516 TAC MODULE THROTTLE ACTUTATOR POSITION PERFORMANCE CONDITIONS * POSSIBLE CAUSES IS TAC MOTOR CKT 1 OR CKT 2 IS OPEN SHORTED TO GROUND OR B+.OR THE THROTTLE ACTUATOR MOTOR CKT 1 IS SHORTED TO CKT 2.OR THE THROTTLE ACTUATOR MOTOR CONTROL MODULE HAS FAILED.

Aug 17, 2009 | 2003 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...