Question about 1986 Isuzu Pickup

1 Answer

How do I replace a seat belt on a 1990 Isuzu pickup?

Posted by on


1 Answer


Posted on Sep 05, 2008


1 Suggested Answer

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1990 Isuzu pickup turns off at stop sign

If this is a petrol engine have a look at the brake booster leaking vacuum and running the engine too lean to idle. Test by allowing to idle with out your foot on the brake If applying brake pressure shuts the engine down ,replace the brake booster..

Jan 24, 2015 | 1990 Isuzu Pickup

2 Answers

Where is the turn signal flasher module on my 1990 isuzu pick-up?

Hi there:
On 1990 Isuzu Truck t he Flasher is located front seating area, driver side, under dash, near fuse panel, taped to dash wiring harness.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 17, 2011 | 1990 Isuzu Pickup

1 Answer

Do I have to disassemble the drive line to tow a 1990 Isuzu P'up on a tow dolly?

if its not AWD, or in 4WD then no, just ensure its in neutral, or you can tow it from the back, just lock the steering wheel, tie the seat belt around it afterwards. We used to do it all the time. It also depends on how far you are towing the vehicle.

Mar 29, 2011 | 1990 Isuzu Pickup

1 Answer

How do i insert a fuel pump on a 1990 isuzu pickup

If it is on the engine you will need to remove the right front wheel then you can get to it.

Feb 28, 2010 | 1990 Isuzu Pickup

1 Answer

Where is the fuel filter located on a 1990 Isuzu pickup with 2.3 liter engine.

The filter is located on the frame rail by the passenger side rear wheel.

Oct 15, 2009 | 1990 Isuzu Pickup

1 Answer

I have a 1993 isuzu pick up newly built need schematics on firing order and distributor rotor location and timing marks and timing belt replacement any help will be thankfull

1993 Isuzu Pickup 2WD
2.3 liter SOHC L4

1993 Isuzu Pickup 2WD
2.6 liter SOHC L4 .......same as above

1993 Isuzu Pickup 2WD
3.1 liter V-6

4wd is the same specs as the 2wd.

Apr 22, 2009 | 1993 Isuzu Pickup

1 Answer

1990 isuzu pickup temp sender location

It is on the underside of the intake manifold near the front directly below where the water hose and thermostat connect on the top
Jack Boersema

Dec 16, 2008 | 1990 Isuzu Pickup

1 Answer

1990 holden rodeo /isuzu pick-up temp sender

from memory it is in inlet manifold some were in front middle section bottom, (underneath) 4ZE1?
single wire possibly yellow

Dec 16, 2008 | 1990 Isuzu Pickup

1 Answer

Replacing broken belts 1990 toyota pickup

I found that it is embarrassingly obvious once you get the parts and place them in position. Each belt only fits the appropriate pulley in width and length. When the belt breaks there's no visual reference (as one would have if he replaced the belts before they broke!) if the belt diagram is worn off the hood. Lesson learned; replace belts- a simple task- before they break!

Nov 17, 2008 | 1990 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

85178 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides