Question about Chrysler Concorde

1 Answer

95 chrysler concorde the speed odmeter,fuel gauge,and overhead light stop working. I replaced ignition switch,dash panel, and checked all fuses. what can i do?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 274 Answers

Did you check all of the fuse panels? Modern cars have anywhere from 2 to 4 fuse panels. One or two in the car and one or two in the engine bay near the firewall and the intake. It could also be bad wiring or a harness that came detatched.

Posted on Apr 07, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my gauge cluster stop working?


they have an issue with the instrument panel connectors, my 05 2500 hd has an intermittent problem where it goes dead and if you smack the dash or hit a bump driving it will reset. It got much better when I put an extra twist in the cable before connecting it. I also got a replacement cluster due to bad lights etc and it does the same as the old one,I think it's a loose pin, probably ground but haven't gotten around to fixing it. my 95 c 1500 did the same

Jul 13, 2014 | 2003 Chevrolet Silverado 2500HD

2 Answers

Gas, fuel, and temp gauge doesn't work


You have blown a fuse..check fuse box. There may be one fuse box one in the cabin but also check for the fusebox in the engine compartment.

Oct 04, 2017 | 1992 Dodge Caravan

2 Answers

1994 CONCORD NO POWER TO FUEL PUMP, NOT FIRING AND DOES TURNOVER, REPLACED CRANK SENSOR AND CAM SENSOR, TRIED DIFFERENT RELAY FOR FUEL PUMP-STILL WON'T START?


NO POWER TO FUEL PUMP......CHECK ALL IN LINE WIRING
NOT FIRING... START WITH COIL PACK, DIST CAP ETC...PLUGS/WIRES??????
"HOT WIRE" (DIRECT W/ FUSED JUMPER) TO FUEL .PUMP....NO - GO,,,BAD PUMP

Oct 09, 2011 | 1994 Chrysler Concorde

1 Answer

The dash board lights and gauges no longer work,where is the fuse location ?


when u open the drivers side door, the dash board side panel come off. you will find the fuse box there

Mar 07, 2011 | 1998 Chrysler Concorde

2 Answers

Need to figure out how to disconnect the factory alarm on a 1994 chrysler concord . Took out the fuses and still is going off.


Maybe in here you can find information about Wiring Alarms:
- Commando Car Alarms (for 1994 Concode)
- 1994 Chrysler Concorde Alarm Information

I hope helpy you with this. Good luck (remember rated this help).

Oct 05, 2009 | 1994 Chrysler Concorde

1 Answer

Gauges stop working and then car will not start


check the ignition swich, may have some bad contacts, try to move it around with the key in it if the gauges go on ,this could be the problem. I had this happen to my car.
check the fuses,. make sure your battery is good.

Feb 03, 2009 | 1998 Chrysler Concorde

1 Answer

My gauges and heat dont work on my car and the check engine light comes on


try to replace the ignition switch mine went bad and either things didnt come on or all the dash lights would stay on

Nov 17, 2008 | 1996 Chrysler Concorde

1 Answer

Will not start, no dash gauges light except "low gas level"


I have a '99 dodge dakota, 4 cyl, 5 speed manual. While researching a no start problem ran across possible solution to this problem. If no guage lights show when key truned to on position then normally a bad ignition switch. With fully charged battery and working ignition switch guage lights should slight up then go out when ignition in "on" position. Try shaking the key back and forth.


Dave

Aug 17, 2008 | 1998 Dodge Dakota

1 Answer

94 Concorde electrical


I have a similar problem with my 94 concorde... and was advised the on board computer was in need of replacement. Further research led to pulling the computer and cleaning the ground connection to the chassis. It will sometimes leak under the computer and corrode, and compromise the ground, which in turn will cause faulty "code" readings and the engine control light to come on.

May 24, 2008 | 1994 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...