Question about Chrysler Fifth Avenue

1 Answer

Car was driving fine I got off the freeway accelerated then the car disengaged and kept disengaging .would engage at low speeds then would not engage in any position reive the engine nothing would happen barely got home checed linkage and fluid all normal but a whining noise happens every time the caris trying to engage or in reveverse

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Im assuming this is a manual transmission, if so you need to replace the clutch assembly. the clutch disk has worn too thin for the pressure plate to hold at higher rpms and soon wont hold at all.

Posted on Apr 07, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does cruise control continue to accelerate when engaged?


If it is disengaged to coast (to a lower speed), it will accelerate to the previous set speed when reengaged. This is experienced often when driving on highways and you have to coast to a lower speed.

Sep 01, 2015 | Cars & Trucks

1 Answer

96 explorer disengages 4wh low but does not engage 2wheel


Does it shift to 4wd high range ? If so then shift to 2wd . What is going on here is the transfer case motor is stopping due to the motor position sensor has gone bad which means that you replace the transfer case motor assembly. But if you wish to make it a 2wd for awhile then remove motor and manually turn shaft . This can be done by raising and supporting rear axle truck in park remove motor turn shaft slowly with pliers and rotating the play in drive shaft. There are stamped markings on back of case showing gear positions..

Mar 31, 2014 | 1996 Ford Explorer

1 Answer

My 2008 Nissan titan will not engage in 4x4 high but will engage 4x4 low. There is also a grinding noise when I try 4x4 on the fly. The light comes on and say it is engaged but it doesn't really engage....


There may be a problem with the syncro rings in the 4x4 high section of the box. It may have something to do with you driving technique by not allowing the synchro rings a chance to bring the mating gear up to speed. When the change is required it should be done at a relative low speed wit either a brake in the accelerator pedal ( lifting the foot for a second) or a clutch disengagement (pushing the clutch in and out for a second). This breaks the load on the gear teeth and allows for the change to be completed

Dec 22, 2013 | Nissan Titan Cars & Trucks

1 Answer

My Audi A4 03 is auto but you accelerate and it's like a clutch engaging and disengaging???


sounds like its low on oil but then i dont get many autos to repair here in spain

Apr 23, 2012 | Audi Cars & Trucks

1 Answer

Transmission disengaged (as if I had put it in neutral) while driving freeway speed. Tried to accelerate and got nothing but engine RPMs.


Unfortunately it sounds like your automatic transmission clutches are worn out but old and dirty oil can also cause this along with a blocked transmission filter, transmission service might get you out of trouble but a transmission specialist would be advisable.

Feb 14, 2011 | 2002 Mitsubishi Diamante

1 Answer

Can I engage and disengage the 4 wheel drive while I'm driving? At what speed?


You can engage from two wheel drive to four wheel drive at any reasonable speed though I find it's easier on the transfer case if you do that below 45mph. Lift you foot off the gas as you shift so the unit is not under stress. To engage 4 low, you should not be traveling faster than 5mph and then, only on slippery surfaces. When in that gear, it is not advisable to travel much faster than 25-30mph and never on dry ground.

Jan 06, 2011 | 2002 Jeep Liberty

1 Answer

I don't know how to put my 1993 jeep wrangler into four wheel drive


To engage the four wheel drive, while rolling, pull the lever back one notch and that will engage the transfer case. You can easily do that up to speeds as high as 35mph. Pulling the lever all the way back will put it into 4 low which is not often used and may grind if it does not engage right away. That really doesn't matter much because that gear is only used for pulling heavy loads at low speeds. (I use mine about once every two years) If you do need to use it, generally you can engage it with the engine off without problems. The neutral position is used to disengage the wheels if the vehicle needs to be towed. If it fails to disengage, often backing up about twenty feet or so will help.

Dec 06, 2010 | Jeep Wrangler Cars & Trucks

1 Answer

1997 Jeep Wrangler 4wd high disengages


you might try checking the linkage on trans case shifter. may need adjusting. might not be getting fully engaged

Feb 06, 2010 | 1997 Jeep Wrangler

1 Answer

1998 Mercesed ML320 sporadic gear disengage when speed up


You need change atf flood and check level.Make sure only mb atf if yuo put wrog atf say good bye to transmission .good luck

Jun 03, 2009 | 1998 Mercedes-Benz M-Class

1 Answer

Dont know how to use my 4wd


You first have the car running and as long as you are going or driving under the speed of 55 mph you can put it in 4 wheel drive high. for low come to a stop put in neatural and switch to low. put in drive and go. max speed 10 mph

Apr 20, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...