Question about Chrysler Concorde

1 Answer

Need to know which fuse is for the brake lights all three stopped working at once

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,761 Answers

It's probably not a fuse -- check the brake light switch that's attached to the brake pedal shaft. Pressing the pedal compresses the plunger, making contact and turning on the brake lights. Manually press and release the plunger several times and see if the light function is restored. If that doesn't work, try a little (VERY little) WD-40 or silicone lube on the plunger. If neither works, you'll need to replace the switch - an easy and inexpensive job.

Posted on Apr 07, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake light is working but not the tail light?


There are three fuses involved.
There is a 25 amp fuse before the brake switch located in the fuse box under the hood. Then there are two 15amp fuses after the brake switch in the box inside the cabin. One is for the lower brake lights and the other is for the high mount light and the trailer connector.
You would need to know if the 15amp fuse for the lower lights has power when the brake pedal switch is applied.

Feb 01, 2014 | 2004 Cadillac Escalade Esv

1 Answer

Brake lights troubleshooting


Hi Tanya, A short circuit in a vehicle is very dangerous. The cause needs to be identified and isolated. Why did you replace the brake light switch and then the indicator switch? Did the fuse blow when operating those units? Let me know more information and maybe we can sort it out? Regards John

Oct 26, 2013 | Cars & Trucks

1 Answer

Nissan Xterra Brake Light Fuse Location


Hi, you need to test if the power is coming to the plug for rear brake light. If the power is not there that is your first problems. Also may have earth wire problem.

Jul 20, 2013 | Nissan Xterra Cars & Trucks

2 Answers

2 out of 3 brake lights dont work


If any light lights up when you apply brakes, then the brake switch is ok. The problem could be a fuse and/or a relay. or the bulbs. Those bulbs are dual filament so one filament could be bad, for stop or tail lights.

Oct 02, 2012 | 2002 GMC Envoy XL

1 Answer

I have a 91 ford f150 and the brake lights wont work and the rear right blinker is dim. Can you help me?


Check System Fuse - A fuse is used to protect the brake light circuit from amperage overload. If the fuse has failed it will not allow the electrical current to continue to the brake lights. To check the fuse, first locate the brake light system fuse in the fuse panel which is either under the dash or under the hood in the power distribution center. Connect the test light to a ground like an engine or dash bracket and turn the ignition key to the "on" position. Using the test light probe both sides of the fuse. If the test light illuminates on both sides the fuse is okay continue onto the next step. If one side of the fuse illuminates the fuse has failed and needs to be replaced. If the fuse fails as soon as it is replaced or when you apply the brake pedal the brake light electrical circuit is shorted to ground. Rarely a system short can occur, a car repair manual is needed to find the wiring schematic for the brake light circuit. Once the brake light wiring has been located inspect and repair as needed.

Check Brake Light Bulbs - All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is okay or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are okay continue to the next step.

Checking the Brake Light Switch - A control switch is used to connect the brake light electrical circuit. This switch is located near the brake pedal lever. Basic switches have just two wires, power in and power out to the turn signal switch. Use a test light that is grounded and with the key in the "on" position test for power at one side (wire) of the switch, then press the brake pedal while testing the opposite side (wire). It should illuminate the test light, if electrical power is connected through the switch go to the next step. If no power is detected through the switch the brake light switch has failed and replacement is required. If your car is equipped with more than two wires integrated into the brake light switch a car repair manual is needed to locate the proper brake light circuit wiring.

Nov 05, 2011 | 1991 Ford F150

3 Answers

All brake lights on my 307 have stopped working at once what could be the problem


Hi,

This is caused by one of two things.

1) Blown fuse - check the fuse box for the fuse that controls the brake circuit. Replace as necessary.

2) Bad brake switch - If the fuse is not blown this indicates a faulty brake switch on the brake pedal itself. This will need to be replaced.

Thanks for using FixYa.

May 30, 2010 | 2006 Peugeot 405

3 Answers

Brake lights do not work All bulbs have been replaced.


Troubleshooting Procedures - Read Completely Before Beginning
(American Car) All Brake Lights Not Working
  • Check System Fuse: A fuse is used to protect the brake light circuit from amperage overload. If the fuse has failed it will not allow the electrical current to continue to the brake lights. To check the fuse, first locate the brake light system fuse in the fuse panel which is either under the dash or under the hood in the power distribution center. Connect the test light to a ground like an engine or dash bracket and turn the ignition key to the "on" position. Using the test light probe both sides of the fuse. If the test light illuminates on both sides the fuse is ok continue onto the next step. If one side of the fuse illuminates the fuse has failed and needs to be replaced. If the fuse fails as soon as it is replaced or when you apply the brake pedal the brake light electrical circuit is shorted to ground. Rarely a system short can occur, a car repair manual is needed to find the wiring schematic for the brake light circuit. Once the brake light wiring has been located inspect and repair as needed.
  • Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.
  • Checking the Brake Light Switch: A control switch is used to connect the brake light electrical circuit. This switch is located near the brake pedal lever. Basic switches have just two wires, power in and power out to the turn signal switch. Use a test light that is grounded and with the key in the "on" position test for power at one side (wire) of the switch, then press the brake pedal while testing the opposite side (wire). It should illuminate the test light, if electrical power is connected through the switch go to the next step. If no power is detected through the switch the brake light switch has failed and replacement is required. If your car is equipped with more than two wires integrated into the brake light switch a car repair manual is needed to locate the proper brake light circuit wiring.

Jul 07, 2009 | 2000 Jeep Grand Cherokee

2 Answers

All three brake lights are out on my 94 Acura integra.


Check the owner's manual. There are fuses under the hood as well as by the driver's side floor, where the hood release is. If the cover is gone go get one at the junk yard. Comes in handy, even a fuse puller and spares in there

Apr 06, 2009 | 1994 Acura Integra

1 Answer

Need fuse schematic


if the fuse was blown the stop lights on both sides would be inop, also if the stop light circuit were dead u would be unable to get the trans out of park, use a 12 volt test light and test the brake light switch at the top of the brake pedal, u can buy a test light from Autozone, kragen and others for about $5 US. If the system has power cjheck the bulb socket it may be defective, use the 12 volt test light while someone pushes the brake pedal. let me know what u find and i will give u further assistance as ness.

Dec 31, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...