Question about Chevrolet 1500

1 Answer

Have fluid in res. lines are free bleeder has fluid but can't get preasure on clutch arm

Posted by on

  • Anonymous Mar 16, 2014

    Fluid in the res.opened bleeder till fluid came out good but I still have no breah preasure.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Clutches can be a pain, do you have fluid bleed out with no air bubbles coming out, if you cant get it to bleed it works best to raise the front of the car up with a jack or as high as you can get it within reason, doing this makes the slave cylinder the highest point therefore air will travel to the highest point making it easier to bleed and get all the air out. if you still cant get it to bleed after that try letting it gravity bleed for a few minutes and then try bleeding and if that dont work possible bad master cylinder. If this is a problem that developed and you have not replaced clutch slave cylinder the slave cylinder is probably the issue

Posted on Apr 07, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 VW Golft GTI vr6 We've replaced the master cylinder and slave cylinder due to the clutch pedal not holding preasure. We then replaced the bearings on the rear rotors. We bled the clutch, and...


When you opened the bleeder screws to the rear brakes, did you completely remove the screws ? Might also want to perform a complete visual inspection of the brake lines from the rear to the front and master cylinder.
How are you performing the bleeding process ?

Jun 19, 2017 | 1996 Volkswagen GTI

2 Answers

How to replace clutch master cylinder and slave cylinder on 2000 hyundai accent?


Starting with the slave , remove the line going to slave then remove the two bolts holding it to the trany and install new one in reverse order, next is the master, from inside the car dissconnect the linkage arm, this is done by removing the clip pin and sliding arm off pedal pin, next remove the resivor and hose. leave hose on resivor remove from master.next remove line from the master then remove the two bolts holding it to firewall, you may have to remove a few things to get the master out this all depends on if theres cruise and a vac valve in the way but this is easy to do.you will need to remove the resivior also when installing new master, bolt it in and connect the linkage make sure the linkage is adjusted as close to the old one as you can leave the adjusting nut a little loose for know after it all connected leave line off and fill with brake fluid have someone inside to push pedal they may have to pull up so you the hand to push and pull pedal, next put your finger over the hole the line goes in and have them push pedal to floor the fluid will push through your finger, do this a few times but watch the fluid level so it doesnt empty, a few time is good then with pedal up remove finger and install line tight,refill with fluid,then have them pump peal three times and hold down, open bleeder at slave, close bleeder and pump pedal again and hold and open bleeder do this a few times until you have a good pedal you will see the slave push out. test the clutch if it works good tighten adjusting nut, if it grabs to soon or doesnt go into gear then adjust, hope this helps.johnjohn2_65.jpg

Feb 20, 2011 | 2000 Hyundai Elantra

2 Answers

Replaced Clutch, master cylinder and slave cylinder on my 85 F250 diesel. The truck shifts ok when it is cold, once it warms up it wont shift using the clutch. you have to use RPMs to make it shift. I...


these are very hard to bleed, also check your fire wall for damage where the clutch master bolts up. another thing is take a good look at the clutch pedal asm, the frame sometimes wears and cracks so you loose a little pedal travel.another thing is a bad preasure plate,spring breaks on plate,

Mar 10, 2010 | 1985 Ford F 250

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

3 Answers

Clutch reservoir is dry on my daughters 96 Eagle Talon the car will not go into any gear.How do I flush the reservoir?If I add oil could this solve the problem


Do not put oil in this system.It uses brake fluid in the reservoir.If the system doesn't have any fluid in it, there is a leak, and both the clutch master cyl and the clutch slave should be replaced. They both were used the same amount of times, and wear evenly. When you add fluid, the clutch master cyl compresses the fluid down the line/hose into the clutch slave cyl. This depresses the clutch fork/arm and disengages the clutch disc so the input shaft into the transmission stops moving, allowing the trans to be put into gear. LOOK FOR THE FLUID LEAKING TO ISOLATE THE PROBLEM. This is a closed system, and the fluid never gets used, unless there is a leak.

Jan 07, 2010 | 1992 Eagle Talon

2 Answers

Straight 6 manual clutch needs bleed


two man job. One guy to pump the pedal, one to crack the bleeder loose on the slave cylinder. only open the bleeder when the pedal is pushed to the floor.tighten the bleeder before letting up on the pedal. Hope this helps.

Oct 13, 2009 | 1985 Ford F150

1 Answer

What does it mean by bleeder .I mean how to bleed the clutch slave cylinder ?


JUst open the clutch slave bleeder valve a little until drips. Let somebody push the clutch pedal. You will
observe the clutch fluid flow initially with bubbles. Stop pushing the clutch pedal upon observing solid flow of the clutch fluid, and close the bleeder valve fast and tight. Bleeding the fluid is releasing the air inside the fluid line going to the clutch master. This in effect gets your clutch good order.

Oct 04, 2009 | 2000 Ford Focus

2 Answers

I have no pressure in the clutch and changed the master cylinder


you need to bleed master & slave cyl master dont hold much fluid must bleed similar like brks when when starts coming out of bleeder close bleeder let sit couple of minutes air travel top of master pump pedal more repeat pumping pedal air residue will work it self out

Aug 11, 2009 | 1997 Pontiac Grand Am

2 Answers

Clutch bleeding


Try opening bleeder screw on slave cylinder and let it GRAVITY BLEED, just open clutch mater and fill with fluid and then open slave cylinder bleeder screw and let it gravity bleed( run out by itself) When it does close bleeder screw and you should get pressure.(make sure master doesn't run out of fluid during this preocess).If pedal not good enough bleed as usual. PUMP PEDAL ABOUT 6 time then hold down to the floor using wrench open slave bleed screw and close back up with pedal still being held DOWN. Repeat until fluid comes out with out air.However if all this doesn't work, YOU WILL NEED TO REPLACE CLUTCH MATER CYLINDER. Conatct if you need more help and Good Luck. Thanks for using FIX YA

Jan 12, 2009 | 2001 Honda Civic

1 Answer

Clutch problem


The bleeder screw or fitting is located either directly on the clutch master cylinder or it will look like a normal bleeder screw on the plastic hardline. with the line cracked open have somebody push the pedal down and hold. Tighten the plug and repeat. Also look under neath your dash, there is a bushing on the clutch pedal arm that car wear out. It should be white in color.

Sep 18, 2008 | 1996 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...