Question about 1994 Geo Prizm

1 Answer

Pos and neg wire in the stereo wires touched and now i have no hazards, turn signals, or power to the stereo what is wrong

Posted by on


1 Answer

The Obvious ---- A Blown Fuse

Posted on Apr 07, 2011

  • baby_jayden8 Apr 07, 2011

    i thought that was it do u know which fuse it would be i have looked and didnt find any that looked bad

  • Anonymous Apr 07, 2011

    Do not know which. Check them all



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What colors are the Speaker Wired for a 1993 gmc 1500 van

    1. OK,GMC/GM are wired as such. White/Black wire, front left -[neg] White, front left +[pos]. Grey/Black wire, front rt -[neg], Grey wire, front rt +[pos]....Green/Black wire, left rear [neg], Green, left rear [pos]....Violet/,Black , Rt rear [neg],...Violet, Rt.rear [pos]........You will also have a Blue/Red wire that goes to antenna. ..A Blue wire for Power Remote....Red goes to IGNITION.....Yellow goes to Battery[for clock].....And finally a Black goes to Ground.......I hope that you have good luck and everything works out for you. `

Sep 07, 2015 | GMC Cars & Trucks

1 Answer

I soldered all the connections on my stereo system and I keep blowing my 5amp fuses I have the yello wire from the head onto pos + on my then I have the black wire on neg .also my red wire is on neg.

check the wiring as the red wire may be a positive power in wire and if you have it on the negative terminal that would amount to a dead short and that would blow the fuse
consider changing the yellow from the + terminal and putting the red wire there and if it stops blowing fuses the put the yellow wire on to the - ve
if that means that the unit doesn't work then touch it back on the + terminal
if that works the solder it there

Aug 13, 2015 | Cars & Trucks

1 Answer

My 77 Chevy c30 has no power. Jumped started it and drove it home. I turned it off then tried to restart it. No power no lights. nothing. Battery is good. An u help will be appreciated.

If the battery is good you will need to follow flow. Test light is the easiest to use. First hook light to ground and touch pos terminal,lights good next touch pos battery cable end, lights good. Next follow pos cable to starter pos terminal,lights good. Next hook test light to bat pos teminal,touch neg terminal,lights good. Then touch engine block, lights good ground. Next move test light clamp back to ground/neg side and touch alt pos terminal,lights good.if all that tests good, if all good move inside and check for power at ign switch pos term if at any time you dont find power you have wiring issue that needs to be addressed. Let me know what you find. Russ

Mar 29, 2015 | Chevrolet Cars & Trucks

1 Answer

Put my battery on wrong neg on pos pos on neg yes plonker moment after wouldn't start checked fuses three blown now replaced car will start but side lights don't work hazards or indicators...

besides checking EVERY fuse in both fuse boxes, check the multitude of relays because chances are some of them are toasted as well. And keep your fingers crossed you have not damaged a CM.
You can wiring diagrams out on the web.

Jan 28, 2015 | Cars & Trucks

1 Answer


turn on a/c does the fan turn on? unplug fan connection mesure voltage comming to the fan it should be 12+ volts. If not it is a fuse or relay. Get some wire that is long enough to reach the battery to the fan plug (have a buddy help) place the 2 wires on the battery connecters 1 pos 1 neg then take the other ends of the wires and touch the wires to the 2 leads in the fan connection. neg wire to the black wire. pos wire to the red. if fan does not come on then the motor is bad. do not worry about touching the battery you will NOT get shocked

Jun 03, 2012 | 1998 Chevrolet Cavalier

1 Answer

Turn signals and hazard lights won't work

you should have pulled the pos battery cable off before you cut the wires and it could be that some of the wires you cut were for the turn signals.

Jan 24, 2009 | 2002 Dodge Stratus

1 Answer

Oem Radio installation

*** 91 park ave with delco bose =

black = ground
dark green = lights on input
grey = panel lights
pink = on input
yellow = power input
orange = battery power input

nca = shield ground
tan = left fr spkr +
orange/black = left & right spkr -neg
lite green = right fr spkr +

nca = shield ground
dark blue = right rear spkr +
dark green/yellow = right & left spkr - neg
brown = left rear spkr +

purple/white = display dim output
pink = vehicle speed input
**** 91 park ave without delco bose =

purple/white = display dim output
pink = vehicle speed input

grey = left front - neg
tan = left front + pos
dark green = right front - neg
light green = right front + pos

black = ground
dark green = display dim signal
grey = panel lights
pink = power antanna
yellow = ign input
orange = battery power
light blue = right rear - neg
dark blue = right rear + pos
yellow = left rear - neg
brown = left rear + pos .

there YA go

Dec 27, 2008 | 1991 Buick Park Avenue

2 Answers

Car stereo wire diagram for 88 toyota tercel

1988 toyota tercel sedan as follows

pink = (+) pos. for left front speaker
violet = (-) neg for left front speaker
light green = (+) pos. for right front speaker
blue = (-) neg for right front speaker
blue/yellow = (+) pos at all times (power)
grey = (+) pos. only in the accessory or run position
brown = (-) neg gound
red = (+) pos. right rear speaker
black = (+) pos. left rear speaker
white = (-) neg right rear speaker
yellow = (-) neg left rear speaker

verified at 2 resources . fixya

Dec 26, 2008 | 1988 Toyota MR2

2 Answers


On some wiring systems you have to make sure the wires are not touching neg. and pos.just try some speakers without actually installing them. make sure mute button is not on.

Oct 25, 2008 | 1998 Ford Escort

Not finding what you are looking for?
1994 Geo Prizm Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides