Question about Ford Futura

1 Answer

Engine turnes over, theres fuel,i changed the coil,checked fuses but no spark engine just stopped while driving

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

Did you try the pickup coil in distibuter

Posted on Apr 06, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 95 Ford crown Vic it will turn over but won't crank,it has half a tank of gas,changed the fuel relays,all fuses good in all fuse boxes but it will not start only turn over I'm lost


check codes first--may find problem there.
check spark on more then 1 cylinder.
check fuel pressure and volume--if fuel filter is stopped up, may have overworked fuel pump. With fuel cap off you should hear fuel pump running (key on) If not running, check for power at sub harness--Lastly tap on bottom of fuel tank with RUBBER hammer while someone else is cranking vehicle--if it starts get it to where you can remove tank before turning off--very often one time deal.

Jan 26, 2015 | 1995 Ford Crown Victoria

3 Answers

Engine stop


If theres no spark from the spark plugs then you would have to replace them?

Jul 12, 2008 | 1993 Toyota Corolla

1 Answer

I've got a 2005 chrysler 300 and it won't start I have changed fuel pump, camshaft and the crankshaft sensor coils and spark plugs and i still wont start what could be causing it not to start?


Try to determine if it is fuel or ignition related.
Turn key to on, do you hear the fuel pump turn on for a couple of seconds? It should come on briefly to pressurize the lines and fuel rail on the engine. Do you have fuel at the engine under pressure? Easiest and preferred way is to check fuel pressure with a pressure gauge at the test port on the fuel rail. With key on, pressure on mpfi systems should be 40-50 psi.
If there is gas in the fuel rail, test ignition by checking for spark on the end of a plug wire, with the engine cranking over. If you have a blue snapping spark, then ignition is probably good-may want to check more than one plug wire. Hold the metal terminal end of plug wire 1/4 inch from a ground on the engine, the engine block or a bolt or metal bracket. Verify a blue snapping spark, repeatedly, as the engine cranks. An orange spark, intermittent spark, or no spark points to an ignition problem. One thing you haven't changed is the ignition control module. This module, when signaled by the pcm, is what cuts the primary current to the coils for spark to be generated.

If you have both gas and spark, check the fuel injector circuit. Post back if you need help with that. There should be an injector fuse that needs checked. Also a fuse for the fuel pump, if no pump action, besides the fuel pump relay.

Apr 04, 2014 | 2005 Chrysler 300

1 Answer

1993 mercury village engine was running was driving down road it shut down, check engine light was on , friend said to change fuel pump and still no spark at engine plugs, what should i try next? is there...


Fuel pumps don't have anything to do with spark. Have the codes read. My guess you lost the crank sensor, ignition module, or coil. Check your fuses also.

Sep 04, 2011 | 1993 Mercury Villager

1 Answer

Not getting fire over the #1 spark plug coil. What needs to be changed/what is the cause of the problem? The engine stopped running while in motion. Battery light came on first then all the other warning...


  1. Check fuel level in fuel tank, add fuel if empty.
  2. Check battery condition and state of charge. If voltage and load test below specification, charge or replace battery.
  3. Check battery terminal and cable condition and tightness. Clean terminals and replace damaged, worn or corroded cables.
  4. Check fuel delivery system. If fuel is not reaching the fuel injectors, check for a loose electrical connector or defective fuse, relay or fuel pump and replace as necessary.
  5. Engine may have excessive wear or mechanical damage such as low cylinder cranking pressure, a broken camshaft drive system, insufficient valve clearance or bent valves.
  6. Check for fuel contamination such as water in the fuel. During winter months, the water may freeze and cause a fuel restriction. Adding a fuel additive may help, however the fuel system may require draining and purging with fresh fuel.
  7. Check for ignition system failure. Check for loose or shorted wires or damaged ignition system components. Check the spark plugs for excessive wear or incorrect electrode gap. If the problem is worse in wet weather, check for shorts between the spark plugs and the ignition coils.
  8. Check the engine management system for a failed sensor or control module.

May 21, 2011 | 2000 Mitsubishi Galant

1 Answer

1989 toyota land cruiser.driving on highway engine died.turns over good but wont start.has a full tank of gas.put in new battery and altenator a few weeks ago,been running fine.checked the fuses and found...


Hi.

Re:new battery and altenator
If engine turns over battery and altenator are OK.

Re:checked the fuses and found a few were blown.
Effectively those may be symptoms of a wiring problem. If a job had been carried recently, undoing and re-connecting the wires to access the part(eg. alternator) may have contributed to the problem.

Check all fuses, with attention to fuel pump fuse. Check the connectors to fuel pump, eventually read volts at pump and nsure that fuel is circulating
Check air intake and connectors to air intake sensors (MAF sensor), check connection to crank sensor and O2 sensors.

The blown fuses may also have been incidental. If you did not find anything, troubleshooting must proceed as usual, checking distribution, fuel pressure, and then factors that can affect the ignition.

Remember that after a prolonged and failed attempt to crank the vehicle, the cylinders will be flooded and the car will no start (wet plugs- no spark).

Check if there is spark on all cylinders. This can be done removing one by one the spark plugs wires and putting them near to the engine block while someone else try cranking. You will see the spark.
If there is no spark, then you have a coil/distribution problem. test coil by reading volts in and impedance (coil must not be open). I think this engine is not distributorless. Check distributor cap and wires. If you have disconnected spark plug wires after the problem, also ensure that wires are connected in right order.

Once you are sure that there is spark, check fuel delivery and engine control. This part will take longer.

I uploaded here engine control diagrams and other documents that may help.

Regards.

Sep 08, 2010 | 1989 Toyota Land Cruiser

1 Answer

95 geo metro 3cyl. 1.0L no spark changed


Pull one or two sparkplugs and check them for moisture; not fuel, but for water beads.
I don't know how long your engine ran after losing coolant but there is a chance that you lost the head gasket and have gotten water into the cylinders.

Nov 26, 2009 | 1992 Geo Tracker

4 Answers

2001 Ford Focus stopped running while i was driving and wont start. Makes a churning sound but no power is going to engine. I changed the ignition coil, still wont turn on. Any suggestions?


Can you explain more so I can help. What do you mean still wont turn on, engines doesn't start or starter motor doesn't turn. Have u taken out a spark plug and connected it to the cable put the end of the spark plug to a ground and make someone turn on the engine for a few seconds you should see some blue sparks. Carefully use gloves. If no sparks, spark plug is bad next thing to check instead of putting the spark plug in the cable put Philips screwdirver put the screwdriver near a ground not touching about one inch make someone turn the engine for a couple of second you should see the spark jumping from the screwdriver to the ground, If there are no sparks ignition coil or spark plug cables are not good. But u say u changed ignition coil so maybe your cables are not good. There is a connector near the ignition coil disconnect it and turn ignition switch on measure the voltage you should have in between 12vdc + or - .5 vdc if no voltage present there is a blown fuse, Check for it

Jul 23, 2009 | 2001 Ford Focus

1 Answer

Engine died while driving, cranks but won't start.


not all scanners a created equal. You need to check for trouble codes...............but it must be fixec by now.

Dec 10, 2008 | 1996 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...