Question about 2007 Maserati Quattroporte Executive GT Sedan

Open Question

I had to have the visors replaced in my 07 Maserati, and now I'm having trouble reprogramming my homelink garage and gate openers. I've held down on buttons 1 & 3 and when the red light starts to flash I release them. Then I press one of the buttons on my garage opener (about 2" away from visor) and one of the buttons but the red light just blinks slowly. It is suppose to blink fast when it has read the device. Thoughts?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2005 Maserati GranSport

Black (Nero) or Silver (Grigio) needs either the Red Rosso) leather or Light Tan (Avorio) to have the maximum impact, I like Avorio.

Posted on Feb 17, 2009

chuck943
  • 783 Answers

SOURCE: I have a 2004 mercury mountaineer 4.0 liter. Had to remove the visor to replace so cut wires to visor light to remove and now the power window along with the radio and gas gauge don't work. Need adv

Check fuse 17(15amp) in the interior fuse panel.

Posted on Apr 17, 2009

  • 1 Answer

SOURCE: sun visor won't go back into place

if its flopping around or feels loose you can try tightening the "hinge" that connects it to the roof and tightening the screws on the visor itself. That might align it enough to fit again properly.

Posted on May 26, 2009

longbow243
  • 103 Answers

SOURCE: sun visor has a lighted mirror, how do I change

Remove the 3 retaining screws and unplug the electrical connector. DONE!

c8fd5ca.gif

Posted on Sep 05, 2009

Testimonial: "easier then I thought. Thanks"

  • 2 Answers

SOURCE: 07 camry - sun visor wont stay and falls forward

Having the same problem. It appears that the tension rod retains tension it appears, but the plastic that surround the sturdy metal tensioner has broken, thus the visor can't hold tension any longer. Very disappointing, looks like I will have to purchase a new one as well. Toyota isn't doing so great these days.

Posted on Jul 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 F-150 no manual.. does this model have a garage door opener built-in ?


It is not standard equipment.
Here is what the manual says (copied and pasted from owners manual)


HOMELINK WIRELESS CONTROL SYSTEM

(IF EQUIPPED )


The HomeLink Wireless Control

System, located on the driver's visor,

provides a convenient way to

replace up to three hand-held

transmitters with a single built-in

device. This feature will learn the

radio frequency codes of most

transmitters to operate garage

doors, entry gate operators, security systems, entry door locks, and
home or office lighting

Feb 27, 2011 | Ford F-150 Cars & Trucks

1 Answer

I don't have the owner's manual for my 2002 GMC Yukon XL Denali. Do you know how to program the garage door opener?


I hope this helps.

Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the stop and reverse
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming HomeLink, make
sure that you have followed the directions exactly as
described and that the battery in the hand-held
transmitter is not weak. If you still cannot program it,
move the hand-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to "Training a Garage Door Opener with
Rolling Codes" later in this section or contact the
manufacturer of HomeLink at 1-800-355-3515,
or on the internet at www.homelink.com.
Be sure to keep the original hand-held transmitter in
case you need to erase and reprogram HomeLink.


Training a Garage Door Opener with a
"Rolling Code" Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see "Programming the
HomeLink Transmitter" listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the "Learn" or "Smartbutton" on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1-800-355-3515, or on the internet at
www.homelink.com.
Because of the steps involved, it may be helpful
to have another person assist in programming
the transmitter.
2. Press the Learn or Smart button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling-code garage door opener should now
recognize HomeLink. You may either use HomeLink
or the hand-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1-800-355-3515,
or on the internet at www.homelink.com.
www.gmcextendedwarranty.com

Dec 19, 2010 | GMC Yukon XL Cars & Trucks

1 Answer

3 buttons on the underside of my 2001 sebring visor


Those are HomeLink buttons. You can program them to work in place of a garage door opener or other infrared device like that. Just pick one, hold it down, press the garage door opener button while aiming it at the visor, and then release the buttons. That allows you to use the visor button instead of a door opener.

Jan 17, 2010 | 2001 Chrysler Sebring

3 Answers

PROGRAM PRIUS GARAGE DOOR HOW DO I PROGRAM THE BUTTONS ON THE PRIUS' REAR VIEW MIRROR TO OPEN THE GARAGE DOOR


There was a minor change for mine to work.. see below..

- you must park your Prius close to the gate opener, leaving it running (obviously not in the way of the gate closing)
- Hold the button the the mirror and then push your garage door remote button and hold until the light on the mirror starts to flasyh fast. THIS programs the button on the mirror, but not the garage opener - yet (this was key for me)
- locate the "learning button" on the opener itself
- press the "learning button" on your gate opener and then get back into the Prius within 30 seconds (more time than it sounds) and press the SAME Homelink button you just programmed above. I don't recall how long I held the pre-programmed button, but the light will flash as I recall.
- Then, when working the garage door, you may need to hold the mirror button for a good second for it to work - but I had tried for months to get mine to work, and finally after reading many posts, the above sequence worked on my 2008 Prius with my Lift Master, Security + rolling codes garage opener.

Just - program the button on the mirror with your remote FIRST.. the garage opener will not work.. then use the Learn button on the garage opener and the SAME BUTTON you just programmed.. and it worked great for me. Not programming the mirror button first will not work. Using only the Learn button will not work. You must program the mirror first with the remote, then use the learn button and the SAME button on the mirror. Hope this helps.

Scott 2008 Prius with Lift Master Security + opener.
-

Oct 30, 2009 | 2007 Toyota Prius

1 Answer

Driver's visor 3 buttons what for and how do i use it infiniti i30


Those buttons are for you to be able to program your garage door opener so that you don't need to have to original clipped to your visor all the time. The procedure is this: 1) put the key in ignition in postition 2 (car not running) 
 
2) hold down both homelink buttons on the outsides of the homelink transmitter (to reset any existing codes) you might have to do it for 20-30 seconds. Red light on homelink will flash rapidly then let go. 
 3) Now, with the garage remote in one hand and hold the button on the homelink you want to program (keep holding homelink until it pulses, not a rapid flash, takes about 20 sec.) While it is pulsing, hold down the garage opener as close to the homeling button as possible while depressing door opener button also.
 
Shortly after doing this you will see the homelink start to flash rapidly (this means it is learning the code). 
 
-  let go of both buttons once it is flashing rapidly and 
 
4) go to motor of door opener and hit the learn button (a light should turn on)
 
5)return to the car a press the homelink button you programmed once, twice, or maybe up to three times until you see garage door open/close.


You may need to have someone help you with this procedure.

Apr 15, 2009 | Infiniti I35 Cars & Trucks

1 Answer

Homelink garage door opener


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

ALSO GOOD GUIDE FOR TROUBLE SHOOTING.

HOPE THIS HELPS

Jul 23, 2008 | 2004 Toyota Camry

1 Answer

How do you program...


The built-in system in your '98 Jeep is made by a company called "HomeLink", a subsidiary of Johnson Controls Inc. The website, www.homelink.com, has a walk through tutorial that should do the trick. It's a matter of taking and existing hand-held remote control for your opener, pressing and holding its button, and pressing and holding the button you wish to use in the visor at the same time (with the remote positioned very close to the visor). The appropriate flashes on the LED above the row of three buttons will let you know when the HomeLink system is set up. Depending on you opener, you may then need to locate a "learn" button on the overhead garage door opener mechanism, and program the HomeLink system into the opener's memory.

Jun 19, 2008 | 2004 Ford Thunderbird

1 Answer

Jag xj6 1996 97 programming the garage door openers


1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.) 2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface (located on your visor), keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)
property_damage_symbol_sm.gif Note: Some garage door openers may require you to replace step 3 with the “cycling” procedure noted in the “View Canadian Instructions” section.
4. Press and hold the trained HomeLink button and observe the indicator light.
  • If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
  • If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener’s manual or contact us. 6. Press and release the “learn” or “smart” button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, there are 30 seconds in which to initiate the next step. 7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the “press/hold/release” sequence up to 3 times to complete the training process.

Jun 13, 2008 | 1997 Jaguar XJ6

1 Answer

Visor Garage Door Opener


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: MOST BUT NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

May 18, 2008 | 1999 Chrysler Sebring

Not finding what you are looking for?
2007 Maserati Quattroporte Executive GT Sedan Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maserati Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Maserati Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...