Question about Toyota Land Cruiser

2 Answers

Cant get rotors off - Land Cruiser Toyota Cars & Trucks

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

I used to have a toyota. on the front of the rotor between the wheel studs there are i think 3 screw holes i don't remember the exact size i think either 8mm or 10mm anyway insert bolts into them tighten one at time it will work the rotor off of the wheel hub

Posted on Apr 06, 2011

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer got voted for 20 times.

  • Contributor
  • 299 Answers

Toyota's require a special screwdriver to to get screw out of rotor.the tool allows you to hit with a hammer to loosen the screw and remove. look close at rotor you will see a screw.

Posted on Apr 06, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to replace rotor/hub assembly on 08 f150

The rotor/hub assembly can be turned; it's done by a lathe that's placed directly on the rotor while it is still mounted on the vehicle. It is called an On Car Brake Lathe.

If you do replace the entire rotor/hub, I suggest buying OEM parts from Ford. There is a major difference in quality over third party vendor parts sold at your local auto parts store; which warp or wear faster...the OEM part has better lasting sealed wheel bearings too

Feb 22, 2017 | Cars & Trucks

1 Answer

Ign. rotor goes on 3 different positions,how do i retime now

an clone rotor H3LL
buy the BOSCH or real GM rotor and guess what, that cant happen.
it must bet be punt on wrong or it make the CMP sensor, NUTS.
so much for $1 rotors. you get what you paid for. for sure.

hell rotors covered here 10 ways from sunday....

Jun 16, 2014 | 1991 Geo Tracker

1 Answer

Cant get rotor off 2000 mazda 626

Hammer time! all the brake rotors I've ever seen just slide on over the wheel lug studs. Your rotor could be seized on there due to rust or excessive heat. tap your way around the back side of the brake rotor and if you can put some heat to the wheel stud areas and it should pop loose. Hope this helps

Nov 10, 2013 | 2000 Mazda 626

1 Answer

Front rotor replacement

I am not familiar with this car, the rotor is one piece with the bearing house? If not, try some lubrication and hit the rotor side with a plastic hammer until the rotor get's loose.

Mar 24, 2013 | 2002 Isuzu Axiom

2 Answers

Cant get rotor off vehicle

Depending on the year and model, it may just be rusty- frozen on the hub. Sometimes you have to use a very large hammer to break it loose. But using a hammer may damage it beyond the point of being useable.

Feb 16, 2013 | GMC C3500 Cars & Trucks

1 Answer

Cant get the rotors off...

you have to remove the brakes and caliper. then your rotor just slides off the studs.

Apr 28, 2010 | 2006 Chevrolet Silverado 1500 2WD

2 Answers

Cant get the front rotors off my 03 mitibushi

check for 1 or 2 cross head screws,(maybe covered in rust.)in between the bolts,then if you have the calipers off hit the rotor with a mallet(or a hammer with a towel on it)to knock it off the hub.(its rusted to the hub,thats all)..

Apr 08, 2010 | 2003 Mitsubishi Outlander

1 Answer

Cant remove rotor on rear of 2005 f150

Sometimes you have to beat them off. You could heat them up. And beat it off. I went as far as cutting them off with a grinder cutting disc but you have to be careful if you cut it off so you don't damage the wheel hub.

Jun 15, 2009 | 2005 Ford F-150

1 Answer

Vibrates when brakes are applied

Oil around the studs and hub with wd40 and let it soak. Then smack the living hell out of it. If you break the rotor it was warped anyway and they aren't that expensive. The best place to smack is between the studs, but be careful not to hit them.

May 19, 2009 | 2000 Mitsubishi Eclipse

1 Answer

Xc90...going to change front rotors myself...need some instruction

I am trying to change my volvo cx90 rotors and brakes. I have manage to get everything off xcept rotors, the rotors are hanging loose but its attached to some bolts which I cant get off, pls can you help with any ideas

Apr 18, 2009 | Volvo XC90 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides