Question about Chevrolet Silverado 2500HD

2 Answers

Stop lights not working on ether side. Cab stop light does work.

Posted by on

  • 1 more comment 
  • stephen glaholt Apr 06, 2011

    Did you get my response?

  • stephen glaholt Apr 06, 2011

    I do not believe any of the steps have proven to be the corrective measures I need. I have had one of the tail brake lights out previous to the other which stopped working months later. I've also found that I get response from both tail brake lights with my emergency flashers? Does that help you?

  • stephen glaholt Apr 08, 2011

    Yes, thank you for all your help. I will use this service in the future.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,654 Answers

Can I ask have you checked the bulbs? are the tailights working just not the brake lights? Have you checked your fuses? Let me know as much as you can and we can get to the bottom of this.

Posted on Apr 07, 2011

  • Dcramer531
    Dcramer531 Apr 07, 2011

    Check for loose grounds at the tailights and also check your brake light switch above the brake pedal.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,382 Answers

Hi, check behind the brake peadle for a little button that pushes in and out when the peadle is pressed(this is your brake light switch) some cars have more than one of theese. manualy let the button out if the light works the switch is good if it does not disconect the harness from the switch and take a small piece of wire and jump the two prongs on the harness if the brake lights come on then you need a brake light switch. if this doesnt work check for power at the switch. if no power you have a bad fuse if there is power and you already jumped the wires to the switch then you have a broken wire between the switch and the tail lights.

Posted on Apr 06, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not shift into gear from park with motor running, also cab lights and electric windows not working. Will start from neutral and then shift into gears.


Might want to start with checking your stop lamps & the fuse for the stop lamps.

The shift interlock is part of the stop lamp circuit on the 97-03 MY trucks, and without working stop lamps, the truck does not come out of park,

Not too sure what you mean by cab lights, is this the interior dome lamps or the instrumentation illumination ?

Apr 10, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

My rear brake lights dont work only the cab light, gmc sierra 6 cyl, what can I look for


your rear stop lights are on a different fuse from the cab stop light. Look in the box under the hood for a fuse marked VEH STOP. See diagram below.

jturcotte_185.gif

Nov 16, 2010 | 2001 GMC Sierra 1500HD

1 Answer

Drove over a huge hole in the road...the bump caused my brake lights and turn signals to stop working...Also the speedometer and other gauges quit working. I cked the fuses and none are blown. What else...


Check the simple things first. A fuse can go bad without "blowing". To check this, get an inexpensive test light. Clip the alligator clip to a good ground. With the fuses in place, (no need to pull them out) you can check the fuse by placing the point of the tester on ether side of the fuse, on the small part of metal that is exposed for this purpose. If just the one side lights up, the fuse is bad. If no side lights up, that particular accessory is not powered on. Next, check the ground wires, the jar could have broken one loose, then you will have to check wiring harnesses, something came loose when you went over the bump. I would start underneath the vehicle. With a flashlight, check for visual damage, paying close attention to plugs. Make sure the plugs are tight together. I am assuming that the "clicking" sound doesn't go at all when you go on the turn signals. If it does, then its probably just the bulbs.

Nov 02, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Interior lights not working


should be under dash on drv side or in glove box

Apr 30, 2010 | 2006 Dodge Dakota

1 Answer

1997 ford f150 - Tail lights stopped working. I have checked the fuses and all are good. I checked the tail lights and the bulbs are good. Any ideas? I have seen posts about some "relays' but I can't...


No relays for rear side lights! will be ether broken wire (unlikley) or corrosion in the connecter to rear (very likely)
Have a good one..........Bruce

Mar 10, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Driver side rear blinker/stop light does not work, also 3rd light stop light isn't working either


may be a bad electronic flasher unit if you lost both. if the blinkers flash very fast, that is a bulb out warning, but sometimes the flasher controls both circuits, and it is a relay.

Jul 22, 2009 | 1999 Ford F150 Regular Cab

1 Answer

2004 Chevy silverado 2500HD the left stop light not working


use a testlight turn on the LS light ground the test light touch the pin inside the lamp socket if it lights look for a bad ground if it does not check your fuses or, run a new power wire under your truck secured with zip ties from the switch

Apr 20, 2009 | 2004 Chevrolet Silverado 2500 Crew Cab

1 Answer

2006 Chevrolet Silverado 2500HD tail lights stopped working


I am having the same problem on an 04 2500hd there isa 15 amp stop light fuse inside the cab on the side of the instrument panel and a 25 amp stop light fuse under hood. you could also have a break switch issue the switch is located up on the break pedal linkage you should have power on the white wire when you push the pedal in (check with a test light) in my case I have a broken wire along the frame rail in the harness it is a light blue wire,

Mar 08, 2009 | 2006 Chevrolet Silverado 2500HD 2WD

2 Answers

2003 silverado 1500 v-6 brake lights dont work


ljones, Did you check the "VEH stop" fuse in the left side instrument panel fuse box. There are 3 stop light fuses, 1 for all the stop lights located in the under hood fuse box. 2 in the left side IP fuse box. 1 for the upper stop light and 1 for the lower stop lights. The fuse box in the IP is where the upper and lower stop lights split. Let me know.

Feb 26, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...