Question about 2005 Hyundai Elantra

Open Question

2005 hyundai elantra with constantly variable valve timing 2.2 how to get the timing marks for the timing chain. I'm trying to put the timing chain back in time because the engine will not crank.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: oil change procedure on a 2005 Hyundai elantra

it is very easy to change the oil put the car on ramps secure the back end look for the drain plug underneath the engine make sure you have the right size wrench and when you remove the plug also check the gasket on the plug to make sure it is not cracked you will also need an oil filter wrench and my other suggestion to you is to go to autozone to see if they have a Haynes repair manual for your car and if they don't see if they can order you one in the mean time they can also print you off a diagram of how to change the oil in you car safely

Posted on Jan 20, 2009

  • 1 Answer

SOURCE: 2002 Hyundai Elantra GLS, headlights burn out constantly

Folks, I had this problem for years...it turned out that the voltage control module on the alterntor wasn't working correctly. It eventually led to a major problem with consistant operation of the vehicle. the dealer couldn't figure it out...it took a seasnoned mechanic to solve the problem. I haven't had a problem since I got the alternator replaced. Wear your gloves when you change them, yes, but don't discount your alternator.

Posted on Dec 26, 2009

  • 184 Answers

SOURCE: 2003 Hyundai Elantra GLS. Check engine light, code PO133

Did you use a aftermarket O2 sensor or a genuine Hyundai one? If it's an aftermarket one it may be bad or not as good as the OEM one. See here for more details and other potential causes: P0133

Posted on Feb 11, 2010

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

  • 510 Answers

SOURCE: Timing marks setting Hyundai Lantra

Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an hyundai elantra 2000 replace timing chain car still won't start what next


check the pints for the timing marks are correct. Do a compression test to see if the valves are bent. It is an interference engine which means that if you moved the cams or crank to line up the timing marks with the cam in position you have bent the valves. If you have done it right then check the firing order

Jan 25, 2014 | Cars & Trucks

1 Answer

Head gasket blown Hyundai elantra '95


New at autozone/napa relatively cheap mark any wires or hoses u remove also get Haynes book it will give step by step to insure a good result in taking apart and back together u got it that far apart also do new timing chain if u are at 100,000 miles or better it will save u headache later thoose are known for breaking and wiping out the valves and everything else when that high in miles good maintenance is always helpful that far tore apart why not be preventive and safe

Feb 21, 2013 | 1995 Hyundai Elantra

1 Answer

2005 hyundai elantra timing belt or chain ?


Belt is my best guess, chains are mostly for v6, v8. i doubt hyundai will use chains

Oct 09, 2012 | 2005 Hyundai Elantra

1 Answer

Fuse for dash lights


if im not wrong it should be with tail lights but i think u have 2 panel boxs also

Sep 30, 2012 | 2005 Hyundai Elantra 2.0

1 Answer

On My 2005 Hyundai elantra 2.0 if I plug my cam sensor in it will turn over but won't start. If I unplug cam sensor it will start but car has a slow start on take off need help?


remove cam sensor clean it put it back in try the car if it still not right replace the sensor you may need to replace crank sensor as well when did it last have a timing belt replaced ?if its got over100 ,000 km on it and hasnt been done i would have it done if the belt brakes it can be fatal for the engine if its old then it may have jumped a tooth wich will put the cam timing out i would look there first turn the engine over by hand till the timing mark on the crank pulley is showing tdc remove the top half of the timing belt cover remove no1 spark plug use a suitable probe to check that no1 piston is at the top if so check the marks on the cam gears are in line with there marks if all marks line up the valve timing is ok

Apr 06, 2011 | 2005 Hyundai Elantra

1 Answer

I have 02 elantra that bent valves 2 times all ready and had it fixed at local machine shop but car still wont start and i am wonderin if its the valve clearence that the shop set on them but i dont know...


Clearance is NOT the issue. The Elantra engine I4 (2.0 lit) is an interference valve-.to-pinston clearance. If the valve timing to piston clearance is exceeded (wether advanced or retarded), the valves will 'kiss' the top of the pistons and get bent. Also verify 'INTAKE' & 'EXHAUST' cams have been installed proprely. Valve timing (timing marks at camshaft sprockets in reference to crank shaft sprocket) is essential. Also,.ensure proper timing belt tension.

Nov 11, 2010 | Hyundai Motor 2002 Elantra

2 Answers

Hyundai troubleshooting code p0010


P0010 is camshaft position actuator malfunction. Hope that helps

Jan 15, 2010 | 2004 Hyundai Elantra

2 Answers

How long should it take to change a timing belt


hi from uk as you do not mention engine litres ? on average it takes approx 2 hours to change belt and tensioner on 1.8=2;0=cv v t 16 valve engines fitted with air con ? simple enough to diy with instructions and timing mark set up b4 you begin dismantle hope this helps ?

Dec 23, 2009 | Hyundai Motor 2003 Elantra

1 Answer

2005 Hyundai elantra sputters - not all the time - no computer codes - garage replaced spark plugs - then purge valve - same problem. it basically hicups.


ask what spark plugs they put in your car. bosch platinums and other aftermarket plugs will give you these symptons. stick to the ngk or champions that came stock

Jul 22, 2009 | 2005 Hyundai Elantra

1 Answer

Timing Belt for 05 Hyundai Elantra


unless your well clued up with engines i wouldn't try changing timing belt yourself get somebody experienced to do this because if you don't time engine up properly you could cause serious damage by bending valves.

Dec 16, 2008 | 2005 Hyundai Elantra

Not finding what you are looking for?
2005 Hyundai Elantra Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...