Question about 2000 Chrysler 300M

1 Answer

Iol pump went out so how do i change it - 2000 Chrysler 300M

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 239 Answers

So what is the condition of your engine at this point? to you really know if it is fried or not? Did someone check toe oil pressure, or is it clattering? If it is clattering, good luck, but have it thoroughly checked out first. A new engine alone is about 3K.
The front cover is in line with your crankshaft and that's where the oil pump is at. Remove the belts, radiator and lower pulley from the engine (parts stores rent them) remove the half dozen bolts from the cover, and the two or four bolts from the oil pan and wriggle it out. It IS expensive though. expect about 200 bucks for just the pump. And while you are at it, a smart DIY'er would change the pan gasket too. Be smart.

Posted on Nov 30, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the hydralic iol in cluc


Open the bleeder valve at the slave cylinder,drain fluid into container,don't reuse.Fill,then bleed.To bleed,pump about 5 times and hold,then open bleeder screw into fluid so air doesn't go back in, continue till air is gone,auto parts have bleeder kits for about 8 bucks.

Jun 03, 2015 | Cars & Trucks

2 Answers

Is it very difficult to change the cam iol seal on a 2.0 toyota rav 4 1999, and is there anything I should know that the book doesn't tell


pulling the timing belt on older RAV4 engines is a more difficult task but not impossible.

Do you have some experience with timing belts and or cars in general?

Apr 05, 2013 | 1999 Toyota RAV4

1 Answer

Oil light came on said shut down motor full of oil


sounds like iol pressure sensor or oil pump failure need to have that checked asap & dont drive it you could make your problem much worse if it is the oil pump

Jul 26, 2012 | Cadillac DeVille Cars & Trucks

1 Answer

Hello, i had an oil change, and a day later my emissions light came on then the car started to chug,sputter or what, like it was not getting gas... I was not having any problems until the oil change...can...


sounds like they have put too much or the wrong oil in the car.. check your manual or call the dealer to find out what oil it takes also check your iol dipstick to see if there is too much or not enough iol in the car. i hope this helps. maby check your air filter too, make sure its clean and the car can breath..

Jul 24, 2011 | 2005 Dodge Stratus

1 Answer

Have 02 ram with 4.7 magnum.......i have loud knock on drivers side down low was pulling a trailer on cruize control at 120km and went about 10 km in passing gear when i let off cruize is when nocking...


could be a piece of that spark plug is embeded in the piston causing it to hit the head on the upstroke.detonation is the cause of the plug failure and must also be addesed. posible lean mix on that cylinder or ignition cross fire.

Jun 07, 2010 | 2004 Dodge Ram 1500

1 Answer

Over heating


could be blown head gasket check to see if your mixing antifreeze and engine oil look at your iol stick and is it blowing smoke through tail pipe you could be loosing compression if head gasket is blown causing over heating, bad water pump

Feb 27, 2010 | 1995 Nissan Pathfinder

1 Answer

Low iol pressure light coming on


could be a sensor. Need to put a gauge on there and check the oil pressure, If ok, replace the sensor. If you have low oil pressure at idle, it is likely the oil pump is shot or the pick up screen is clogged with debris. In either case, this is going to require major repairs.

Jun 01, 2009 | 2005 Pontiac Grand Prix

1 Answer

NEED TO REPLACE OIL PRESSURE SENSOR


usually that sensor is on oil pan or the block in the front of engine.

Mar 27, 2009 | 2003 Hummer H2

1 Answer

To much iol


HOW OLD IS YOUR PUNTO & IS ENG LIGHT ON?

Dec 30, 2008 | 2006 Fiat 124

Not finding what you are looking for?
2000 Chrysler 300M Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...