Question about 2004 GMC Sierra 1500 Crew Cab

Open Question

Trying to locate the power mirror fuse for a 2004 gmc sierra slt extended cab. Neither mirror works but signals on mirrors do

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Power Window in a 2001 GMC Sierra Extended Cab

i just changed my unit on drivers side door man it was a pain well first it started off with not going at all i thought it was the motor but motor was good the wire was just getting hung up because the plastic piece broke on the track,so first disconnect motor from track and hit switch to see if it turns,and if not then replace motor,be careful not to loosen the cable.you almost need it exact tension for the track to work right.   

Posted on Mar 30, 2009

raffaiel
  • 209 Answers

SOURCE: Loose side mirror. Need to tighten it up.

just remove the panel inside at the side of the mirror, then you will find the bolts.

Posted on Apr 25, 2009

  • 2 Answers

SOURCE: 2003 Sierra rearview mirror

replace outside sensor

Posted on Feb 28, 2009

  • 124 Answers

SOURCE: where is the 4x4 encoder motor sensor located on my 03 sierra

the encoder motor sensor is inside the encoder motor. the encoder is located at the transfer case. Remove the encoder and by part number 88962315 this is the sensor. you will have to retime the motor after
hope this helps

Posted on May 06, 2009

  • 1 Answer

SOURCE: My GMC sierra side mirror is loose on from the

I just spent about 2 hours trying to resolve the same problem, and discovered that there doesn't appear to be any way to repair the mirror without purchasing a whole new one. There a 3 screws you can access by slanting the mirror to the extemes in both the up or down positions. Once they are removed I discovered a 4th screw (once I broke the plastic pieces surrounding the mirror appart) that there is a 4th screw that is impossible to reach without removing the actual mirror part. In any case I discovered that the reason that the mirror was floppy is because there was a funny looking nut that is supposed to lock in the spring mechanism that was completely stipped and non functional. Better luck than me!

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for cigarette lighteron 2003 GMC Sierra SLT extended cab


Pop the hood. Find the square black fuse box on the driver side (Same side as the windshield washer jug and battery). Pull the top off the fuse block. There will be a label under the lid indicating what the fuses do. The cig lighter fuse is in this fuse block.

Apr 20, 2015 | 2003 GMC Sierra

Tip

On truck the 2004 GMC Truck Sierra you have on the dash a driver information...


Put the control (on the driver door for your side view mirrors) onto the passenger mirror position put the car in reverse, mirror tilts down and shows you the curb! (this only works on some models like the 3.0 not sure of what year of 1.8t)

on Mar 14, 2009 | 2006 Audi A4

2 Answers

Where is the turn signal relay located on a 2004 GMC pick-up


The relay is either under the hood in fuse box or in fuse box on leht side of dashA thumbs up would be greatly appreciated if this answer is helpful to you. turn-signal-relay-located-2004-gmc-pick-2k13k1xkrzqcnxretqgjtz4k-5-0.jpg

May 23, 2012 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

2004 GMC Sierra 2500 HD. Drivers side mirror was


You should be able to replace the glass, but I believe it is glued in place. You should be able to tell as you remove the old pieces. It is a special white glue.
I was able to get a great price for the whole mirror on ebay. even the ones with signals and heated.

Hope this helps

Jan 09, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

2004 GMC Sierra Power Mirrors do not work


FUSE AND MAYBE LOOSE WIRE CONNECTION

Oct 30, 2009 | 2004 GMC Sierra

1 Answer

2003 gmc mirrors do not fold in


The power mirrors are controlled by a module (computer) DDM - drivers door module an the PDM - passenger door module .
Folding Mirror System
Folding Mirror System Controls
The folding mirror system requires signals from 2 separate switches. The mirror select switch must be in the neutral/fold position and the mirror direction switch must be activated to the left/extend or right/retract positions. Both switches are integrated into the DDM and provide direct signals.
Folding Mirror System Operation
Upon receipt of the required switch inputs the DDM will supply battery voltage and ground to the mirror fold motor control circuits to perform the requested extend or retract function. The DDM will also send a class 2 message to the PDM indicating the requested function. The PDM will supply battery voltage and ground to the mirror fold motor control circuits to perform the requested extend or retract function.

Power Mirror System
Power Mirror System Components
The power mirror system consists of the following components:
• The driver door module--Class 2 module with integrated switches and requires programming when replaced
• The passenger door module--Class 2 module with integrated switches, requires programming when replaced and also contains the RFA receiver
• The power mirror direction switch--Integrated into DDM and is a 4-position momentary switch that provides a signal input to the DDM for up, down, left/extend and right/retract with a mirror switch activation
• The mirror select switch--Integrated into DDM and is a 3-position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• The left outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The right outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The body control module--Class 2 module that requires programming when replaced, serves as the power mode master and is the main message handler
• The DDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The PDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The memory switch, if equipped with memory mirrors--Supplied power by the DDM and provides a voltage signal to the DDM upon a switch activation
• The horizontal and vertical position sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDM/PDM and provide a variable voltage signal to the DDM/PDM that is proportional to mirror position
• The park neutral position switch, if equipped with memory mirrors--Provides transmission gear selection information to the PCM and is used for memory recall and mirror tilt in reverse functions
• The powertrain control module, if equipped with memory mirrors--Class 2 module that requires programming when replaced and provides Class 2 message indicating transmission gear selection
• The driver information center (DIC), if equipped with memory mirrors--Part of the instrument cluster which is a Class 2 module that requires programming when replaced and is used to personalize the memory recall and mirror tilt in reverse functions
• Fold motor in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Each of the outside power mirrors contains 2 reversible motors to provide horizontal and vertical movement of the mirror glass. The vertical motor operates the up and down directions and the horizontal motor operates the left and right directions. If equipped with power folding mirrors, each outside power mirror will contain a reversible fold motor to operate the extend and retract functions. Each of the mirror motors are circuit breaker protected.
DTC B1722
The driver door module (DDM) and passenger door module (PDM) switch the mirror fold motor control circuits to battery voltage and ground in response to mirror extend or retract command.

Apr 06, 2017 | 2003 GMC Yukon XL

1 Answer

Electric Mirrors do not work (Drivers & Passengers)


There are two power wires to the DDM - drivers door module .Both are orange ,one is powered by a fuse DDM fuse 15amp . in the left I/P fuse block , plus LT DOORS 25amp circuit breaker .
Power Mirror System Components
The power mirror system consists of the following components:
• The driver door module--Class 2 module with integrated switches and requires programming when replaced
• The passenger door module--Class 2 module with integrated switches, requires programming when replaced and also contains the RFA receiver
• The power mirror direction switch--Integrated into DDM and is a 4-position momentary switch that provides a signal input to the DDM for up, down, left/extend and right/retract with a mirror switch activation
• The mirror select switch--Integrated into DDM and is a 3-position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• The left outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The right outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The body control module--Class 2 module that requires programming when replaced, serves as the power mode master and is the main message handler
• The DDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The PDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The memory switch, if equipped with memory mirrors--Supplied power by the DDM and provides a voltage signal to the DDM upon a switch activation
• The horizontal and vertical position sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDM/PDM and provide a variable voltage signal to the DDM/PDM that is proportional to mirror position
• The park neutral position switch, if equipped with memory mirrors--Provides transmission gear selection information to the PCM and is used for memory recall and mirror tilt in reverse functions
• The powertrain control module, if equipped with memory mirrors--Class 2 module that requires programming when replaced and provides Class 2 message indicating transmission gear selection
• The driver information center (DIC), if equipped with memory mirrors--Part of the instrument cluster which is a Class 2 module that requires programming when replaced and is used to personalize the memory recall and mirror tilt in reverse functions
• Fold motor in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Each of the outside power mirrors contains 2 reversible motors to provide horizontal and vertical movement of the mirror glass. The vertical motor operates the up and down directions and the horizontal motor operates the left and right directions. If equipped with power folding mirrors, each outside power mirror will contain a reversible fold motor to operate the extend and retract functions. Each of the mirror motors are circuit breaker protected.

Do you know what DTC'S are ? Diagnostic trouble codes
DTC B1544, B1600, or B1605
DTC B1580, B1590, B1610, or B1620
• If DTC B1580 is set by itself, the left horizontal position sensor signal circuit maybe open, shorted to ground or battery
• If DTC B1590 is set by itself, the left vertical position sensor signal circuit maybe open, shorted to ground or battery
• If DTC B1610 is set by itself, the right horizontal position sensor signal circuit maybe open, shorted to ground or battery
• If DTC B1620 is set by itself, the right vertical position sensor signal circuit maybe open, shorted to ground or battery.
• If DTCs B1580 and B1590 are both set, the left 5 volt reference or low reference circuit(s) maybe open, shorted to ground or battery.
• If DTCs B1610 and B1620 are both set, the right 5 volt reference or low reference circuit(s) maybe open, shorted to ground or battery.
Need a factory scan tool to test !
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, observe the mirror horizontal and vertical position parameters in the Driver Door Module (DDM) and Passenger Door Module (PDM) data lists.
Operate both the left and right mirrors through the full range of movements.
Does the scan tool indicate that the left and right mirror horizontal and vertical position parameters are within the specified range?
0.50-4.75 V.
Your best bet , take it to a GMC , Chevy , buick or cadillac dealer

Apr 16, 2017 | 2003 GMC Sierra 2500HD

1 Answer

I have a 2005 GMC sierra with power, heated mirrors.


Yes, you can find them here http://www.muthco.com/products/kits/200-0036.htm.

Mar 22, 2009 | 2000 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...