Question about 2000 Nissan Pathfinder

1 Answer

2000 nissan pathfinder it runs but runs ruff i have changed all plugs an wires a new distuber..i have also changed the knock sensor too..the truck still has a miss fire an a ruff idle..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Nissan Master
  • 1,949 Answers

Fuel filter?

Posted on Apr 06, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the knock sensor in a 1995 nissan pathfinder v6


http://forums.nicoclub.com/96-pathy-knock-sensor-location-t483742.html

Apr 13, 2017 | Nissan Cars & Trucks

3 Answers

Where is the knock sensor located at on a 97 nissan pathfinder?


images for Where is the knock sensor located at on a

1999 Nissan Pathfinder 3.3L Knock Sensor Relocation (also ...

? 10:37
https://www.youtube.com/watch?v=2t1l68s8MmM
Aug 14, 2010 - Uploaded by Dan Russell
Tools/Parts needed: Nissan Pathfinder Knock Sensor ($25): from ... Dan I have a 1997 infinity qx4 and ...

Nov 28, 2015 | 1997 Nissan Pathfinder

1 Answer

2000 Nissan Pathfinder Rough Idle, Hesitating on Acceleration, Misfiring/Backfiring


Ok P0325 Knock sensor (Bank 1) There is a way to test the resistance, but I dont know the specific Ohms for your vehicle.
P0400 EGR Flow This means that there is a buildup of carbon and other things in all the passages that go to the EGR. Clean them out before looking at the knock sensor. Bad misfires can cause the knock sensor to go out of range. EricTheCarGuy has some excellent videos (youtube) explaining how to go about this.

Jun 08, 2013 | 2003 Chevrolet Silverado 1500

4 Answers

Will the knock sensor affect the way a 97 nissan pathfinder runs?


It will! if it goes bad, it changes the timing and runs bad

Jan 19, 2013 | 1997 Nissan Pathfinder

1 Answer

2000 pathfinder sluggish and quits. replaced knock sensor as it showed a code for that and it ran for about a week now it has quit


bad catalytic converter? if your exhaust system is plugged or exhaust flow is reduced too much car will not start. while your at it buy a oxygen sensor too cant hurt. good luck

May 25, 2012 | 2000 Nissan Pathfinder

3 Answers

My 1997 nissan pathfinder p0325 code came up on the scanner, and I need to change my knock censor on the car. I do not known were this part is located on the engine


very familiar with this. it is down under the intake manifolds in the valley of the engine. it is a single wire connector. you must remove the manifolds to replace this item. parts will run you about $100 and take about 3-6 hours depending on your compentance. parts needed are 1. knock sensor 2. intake(upper and lower plenum gasket)set 3. coolant. make sure you drain your radiator prior to doing this as to not allow a bunch of coolant to drain into the cylinders and cause hydrolocking. if this happens you must remove the spark plugs and rotate the engine to spray out the liquid out of the cylinders then reinstall.

Dec 24, 2009 | 1997 Nissan Pathfinder

1 Answer

Trouboule


A P0325 refers to the knock sensor electrical circuit, not the sensor itself! So check all wiring & connectors leading to the sensor, back to the PCM. Good luck, I found a good P0325 article here - http://www.obd-codes.com/p0325

Oct 19, 2009 | Cars & Trucks

1 Answer

Nissan


OK the sensor may not be bad, you might have a broken wire to the sensor. Or a bad plug, I would by pass the sensor plug - cut it out. Cut one wire at the time and reconect using a crimp on union (bu**) conector. You may also have a timing issue, that a tune up might fix..

Oct 17, 2009 | 2002 Nissan Pathfinder

2 Answers

2000 nissan xterra knock senor and plug 5


Have you changed all the plugs to platinum and wires? My xterra was doing that and I changed all of them and now it runs great. Also, I changed the distribitor cap and rotor button.

Jun 10, 2009 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Pathfinder Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...