Question about Chevrolet S 10

1 Answer

1998 s10 4x4 front end will not stay in line - S 10 Chevrolet Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 215 Answers

I am assuming your saying the vehicle will not hold an alignment. Reasons for that are ball joints, tie rods, pitman arm, and or control arm going bad.

Posted on Apr 06, 2011

  • Lucy Albert
    Lucy Albert Jan 10, 2014

    Had all that done still won't stay lined up,didn't do this until I put new tires on it

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Chevy Blazer LS...Replaced driver side sway


need too have the front end lined up and probly need too replace the tie rod ends

Sep 21, 2014 | 1998 Chevrolet Blazer

2 Answers

98 ford windstar front end shakes while accelerating


a good thing to check would be your inner and outer tie rod ends. if they are going bad they will cause a lot of shaking in the car and will also cause the front end to be out of a lined which will make your tires wear faster and uneven

Feb 21, 2013 | 1998 Ford Windstar

2 Answers

Where is the fuel filter located on a 1998 oldsmobile 88


Under the vehicle just in front of the fuel tank.

Sep 01, 2011 | 1998 Oldsmobile 88

1 Answer

Transmission line...need to find out about the clips that hold the transmission line, how to reattach the clips


these are commonly called "quick release fittings". pull back the retainer,insert the end of the line into the fitting,and push the retainer back into place.
The little clip that comes with it,can be installed into the retaining slot with a pair of snap ring pliers,or like i do,place one end in the slot,and push the other end with a screwdriver till it snaps into place.

The strange thing iI found with these things is that they seem loose,until you start your truck,and the pressure build up. After that they stay super tight.

May 04, 2010 | 1998 GMC Suburban

1 Answer

I have an ABS light problem on my GMC mod 1998, when i change the rear diferentiel , is there any link to the front break


what is the nature of your problem light staying on going off coming on? the problem started after the rear end change? The EHCU has 2 lines going into it and 3 out. The 2 "in" are from the combination valve, 1 for rear system and 1 for front system. The 3 "out" are split into 1 for rear brakes and 2 for front brakes. check this out and let me know to further help you

Dec 24, 2009 | 1998 GMC Jimmy

1 Answer

1998 chevy z71 1500


Crawl underneath and look for disconnected or damaged wire or vacuum line to transfer case or front axle.

May 01, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Clunk in 4x4 1998 f150


Start by checking the axle half shaft u joints and then the drive line u joints for worn or loose end caps. Also if you have a constant velocity joint on the front drive line make sure the centering ball and socket are not worn. Most people never grease this item and by the time you figure it out it's too late.

Mar 16, 2009 | 1998 Ford F150 Regular Cab

1 Answer

2001 GMC 2500 4WD problem


check all lines some have vacum or small elc. motor on front gears

Dec 13, 2008 | 2000 GMC Jimmy

2 Answers

98 jeep grand cherokee all time 4 wheel drive


i believe your talking about the slip joint dealer should have parts

Oct 24, 2008 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...