Question about GMC Sonoma

1 Answer

I have a rattle in front bumper, how to tighten it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 651 Answers

Find it and tighten it.

Posted on Apr 06, 2011

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: bumper has slipped down about 2 inches on the driver side of the

You must have just typed this because it was runnig across the bottom of the page as i was serching for it......

Posted on Apr 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front end noise


front brake pad hardware is worn out , causing pads to move around when jarred , applying brakes tightens pads and noise will go away

Jul 18, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Front bumper of my 2010 Tucson (not ix35) rattles unbelievably. How do i take it of to add rubber at the squircking spots? It is still under quarentee, but support is lacking to resolve this problem. Can...


Open the bunnet, you will see some screws, just loose them then check by the tire side, you will find another bolt there, loose it then pull out the bumper.

Aug 30, 2011 | Hyundai Tucson Cars & Trucks

1 Answer

Vibrating rattle in front of the car that stops


Wheel nuts are loose. Tighten them asap!

Nov 26, 2009 | 2003 Mitsubishi Lancer

1 Answer

Chrysler 300c rattle in bumper rear


Fold dollar bills and wedge them into the gap of area rattling.

Aug 24, 2009 | 2006 Chrysler 300

1 Answer

Change headlight


hello. below is the procedure for removal of the headlamp for bulb replacement. to access the headlamp you will need to remove the bumper fascia. http://gsi.xw.gm.com/image_en_us/gif/000/001/725/1725371.gif Callout Component Name 1 Front Compartment Sight Shield Plastic Retainers (Qty: 6) 2 Front Compartment Sight Shields (Qty: 3) Tip Each front compartment sight shield is serviced separately as needed for repairs http://gsi.xw.gm.com/image_en_us/gif/000/001/728/1728611.gif Callout Component Name Preliminary Procedure Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement . 1 Front Fascia Extension Plastic Retainers (Qty: 5) 2 Front Fascia Extension http://gsi.xw.gm.com/image_en_us/gif/000/001/733/1733942.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedures Remove the front compartment sight shields. Remove both front bumper fascia extensions. 1 Front Bumper Fascia Reinforcement Nut (Qty: 2) Tighten 6 N·m (53 lb in) 2 Front Bumper Fascia http://gsi.xw.gm.com/image_en_us/gif/000/001/736/1736893.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedure Remove the front bumper fascia. 1 Headlamp Nut (Qty: 1) Tighten 6 N·m (53 lb in) 2 Headlamp Bolts (Qty: 3) Tighten 6 N·m (53 lb in) 3 Headlamp Assembly

Jun 13, 2009 | 2003 Cadillac CTS

1 Answer

Bumper has slipped down about 2 inches on the driver side of the


You must have just typed this because it was runnig across the bottom of the page as i was serching for it......

Apr 05, 2009 | 1994 Cadillac Eldorado

1 Answer

Front bumper of 94 cad eldorado slipping on driver side - need to


There are 4 points of attachment for the front bumper. The nose has two long bolts that go through each of the 2 horizontal shock absorbers and screw into clips attached to the bumper reinforcement. You can access each bolt head with a long socket extension inserted in front of the fog lights.

The remaining two points of attachment are on the side of each of the front fenders, they are plastic guides that meet up with groves on the inside of the bumber sides, as you slide the bumper onto the reinforcement bumper, you line up the bumper groves with these plastic fender-mounted guides and you will reach a point where the bumper snaps in place.

I suspect the driver side bumper sliped out of the inner grove (best caes scenario), or the bumper goves cracked or the plastic fender-mounted guide cracked.

Get under the car to take a look, alternatively undo the 2 front nose bolts and remove the bumper, actually not a big job, and you will then be able to assess the problem.

Hope this helps.

Apr 05, 2009 | 1994 Cadillac Eldorado

1 Answer

Front end rattle


It's a loose steering column. Remove the black plastic shield under the steering wheel. Lossen the bolt that holds the two shafts together, slide them together as far as they'll go, and re-tighten the bolt. It's that simple... to stop that annoying rattle.

Mar 06, 2009 | 2005 Chevrolet Equinox

2 Answers

Need to replace headlight assembly on 2005 Ford Escape


ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

n0037234.gif
Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 3 headlamp assembly bolts.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the headlamp assembly nut and the headlamp assembly.
    • Disconnect the electrical connectors.
    • To install, tighten to 5 Nm (44 lb-in).
  1. To install, reverse the removal procedure.

Jan 01, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...