Question about 1990 Daihatsu Rocky

3 Answers

Ball joint - 1990 Daihatsu Rocky

Posted by on

  • johndz Aug 06, 2008

    my problem is that it has not passed warrant and i want to replace them. is it a difficult job and special equipment needed? appreciate help johndz

  • March Palone
    March Palone May 11, 2010

    What would you like to do with it?

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Just use a 4ft breaker bar to bust it off of the A-frame and it is pretty much easy after that

Posted on Jan 19, 2009

  • thatmug Jan 19, 2009

    Dangit!! Sorry. I somehow thought we were talking about cv joints. disregard. To all those seeking answers to the rocky just go ebay and buy the factory service manuals. i think that i got mine for arund $60 with a wiring diagram

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go to supercheap or repco and buy a ball joint breaking fork. smack the old ones out. put the new ones in with a G clamp and a piece of pipe

Posted on Oct 23, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 167 Answers

Hello. well your ball joint's are connected to your steering .!!! they are connected to the tye rod's the alow you to turn your wheel's .! from left to right.!!! hope this help's you. good luck"

Posted on Aug 06, 2008

1 Suggested Answer

SOURCE: removing lower ball joint ball joint is removed to

Pull steering knuckle/bearing off axle

Posted on Dec 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Whats the part number for a front passenger side lower ball joint on a 96 dodge stratus?


SponsoredShop for Whats the part number fo... on Google
Moog K500007 Lower Ball Joi...
$33.26
Jet.com Moog K6117T Ball Joint
$27.79
Walmart Parts Master K9385 Lower...
$10.97
Jet.com Control Arm W/ball Joint Fr...
$59.70
eBay Ball Joint ? Lower/Upper...
$22.95
EPI Performa... Search Results

    Ball Joint - Lower at AutoZone.com - Best Ball Joint - Lower ...

    www.autozone.com/suspension-steering-tire.../ball-joint-lower

    AutoZoneShop for Ball Joint - Lower products with confidence at AutoZone.com. Parts are justpart of what we do. ... Duralast/Ball Joint - Lower, Part Number: FA1490 ...

    Dodge Stratus Ball Joints ' eBay

Dec 06, 2015 | Dodge Cars & Trucks

1 Answer

Trying to change my upper ball joint. Passager side


For your problem,check out this few help links.

Click the link below to go through its procedure:----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html------- How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html------- How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html------ How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html----------- How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html--------- Lower Ball Joints replacing on Mitsubishi car? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html
-------------These details will help.For more help,keep updated,with car brand,model and year.Thanks.Helpmech.

Oct 05, 2012 | Cars & Trucks

2 Answers

How to replace ball joints on a 1998 mercedes benz s420


For ball joints issue.Before replacing it,first inspect and test the ball joints to confirm the problem:----Click the help links below to troubleshoot the problem and replace the ball joints:----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html Lower Ball Joints replacing? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html----------This will help.Thanks.

Jan 31, 2012 | 1991 Mercedes-Benz 420

1 Answer

Have had to replace ball joints 3 times on my 97 lumina, any ideas why


Always use original parts instead of aftermarket products.Original parts cost bit extra,but they are exact fit and last longer.Click this link below to troubleshoot the issue :----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html Lower Ball Joints replacing on car? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html
---------This will help.Thanks.

Jan 17, 2012 | 1997 Chevrolet Lumina

1 Answer

Ball joint repair and how do you do it


To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.

  1. Using a screw driver or other suitable tool, pry the seal boot off of the ball joint assembly
  2. Position receiving cup, Special Tool 6758 to support lower control arm when removing ball joint assembly. Install Remover, Special Tool 6919 on the top of the ball joint assembly.
  3. Using the arbor press, press the ball joint assembly completely out of the lower control arm.

NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.

  1. By hand, position ball joint into ball joint bore of lower control arm. Be sure ball joint is not cocked in the bore of the control arm, this will cause the ball joint to bind when being pressed into control arm.

 

  1. Position control arm with installed ball joint, in an arbor press with Receiving Cup, Special Tool 6758 supporting the lower control arm. Then center Installer, Special Tool 6908-4 on the bottom of the ball joint
  2. Carefully align all pieces. Then press the ball joint into the lower control arm until it is completely seated against surface of lower control arm. The ball joint is correctly installed when there is no gap between the ball joint and the lower control arm. Do not apply excessive force against the ball joint or the lower control arm.
  3. Install a NEW seal boot by hand as far as possible on the ball joint. Installation of the seal boot is to be with the shield positioned as shown.

CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.

  1. Place Installer, Special Tool 6758 over seal boot and squarely align it with bottom edge of seal boot. Apply hand pressure to Special Tool 6758 until seal boot is pressed squarely against top surface of lower control arm.

CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.

CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.

  1. Reinstall lower control arm on vehicle.

Mar 07, 2011 | 2000 Dodge Caravan

1 Answer

How to remove upper and lower ball joins on a 4x4 bronco full size 1986


For Lower & Upper Ball Joint Step by Step :

For That you use a C-clamp style ball joint press to remove the ball joint from the suspension arm-note the location of the receiver cup ! For installation of the ball-joint, use the same tool when pressing the ball joint into the suspension arm-again, note the location of the receiver cup.

Step by Step :

  1. Raise and support the vehicle safely, with jackstands.
  2. Remove the spindle and the ball joint assembly from the vehicle.
  3. Remove the snapring from the ball joint. Using a ball joint removal tool, remove the ball joint from the spindle. Do not heat the ball joint or the axle to aid in removal.
  4. Installation is the reverse of the removal procedure. Torque the ball joint stud nut to 85-110 ft. lbs. for 1983-89 Ranger and Bronco II.

    Please Rate, Thank you !

Aug 13, 2010 | 1994 Ford Bronco

1 Answer

Front brake rotors.


1. Loosen the wheel nuts slightly. 2. Raise the front of the car and support it with safety stands in the proper locations. 3. Remove the wheel nuts and front wheel. 4. Remove the brake hose mounting bolts. 5. Remove the caliper bracket mounting bolts, and hang the caliper to one side. CAUTION: To prevent accidental damage to the caliper or brake hose, use a short piece of wire to hang the caliper from the undercarriage. 6. On ABS equipped vehicles, remove the wheel sensor wire bracket, then remove the wheel sensor from the knuckle but do not disconnect the wheel sensor connector. NOTE: Use ball joint removers to separate the ball joints from the suspension or tie-rod end. 7. Clean any dirt or grease off the ball joint. Remove the cotter pin from the tie-rod end ball joint castle nut and remove the nut. 8. Apply grease to the special tool on the areas shown. This will ease installation of the tool and prevent damage to the pressure bolt threads. 9. Install a 10mm hex nut on the ball joint. Be sure that the hex nut is flush with the ball joint pin end to prevent damage to the threaded end of the ball joint. 10. Adjust the jaw spacing by turning the pressure bolt. NOTE: If necessary, apply penetrating type lubricant to loosen the ball joint. 11. Once the tool is in place, turn the adjusting bolt as necessary to make the jaws parallel. Then hand tighten the pressure bolt, and recheck the jaws to make sure they are still parallel as pictured above. 12. With a wrench, tighten the pressure bolt until the ball joint shaft pops loose from the steering arm. WARNING: WEAR EYE PROTECTION. THE BALL JOINT CAN BREAK LOOSE SUDDENLY AND SCATTER DIRT OR OTHER DEBRIS IN YOUR EYES. 13. Remove the tool, then remove the nut from the end of the ball joint and pull the ball joint out of the steering/suspension arm. Inspect the ball joint boot and replace if damaged. 14. Remove the cotter pin from the lower arm ball joint castle nut, and remove the nut. 15. Install a 12mm hex nut on the ball joint. Be sure that the hex nut is flush with the ball joint pin end, or the threaded section of the ball joint pin might be damaged by the ball joint remover. 16. Use the ball joint remover, 32mm, as shown to separate the lower ball joint and lower arm. NOTE: If necessary, apply penetrating type lubricant to loosen the ball joint. 17. Remove the knuckle protector. 18. Remove the cotter pin from the upper ball joint castle nut, and remove the nut. 19. Install a 10mm hex nut on the ball joint. Be sure that the hex nut is flush with the ball joint pin end, or the threaded section of the ball joint pin might be damaged by the ball joint remover. 20. Use the ball joint remover as shown to separate the upper ball joint and knuckle. NOTE: If necessary, apply penetrating type lubricant to loosen the ball joint. 21. Pull the knuckle outward and remove the driveshaft outboard joint from the knuckle by tapping the driveshaft end using a plastic hammer, then remove the knuckle. 22. Remove the knuckle from the hub unit. 23. Remove the four flange bolts, then separate the hub unit from the brake disc.

Jun 08, 2009 | 1994 Honda Accord

1 Answer

Replace ball joints


Remove in this order: wheel, loosen the 4 lower ball joint set bolts, cotter pin and nut from tie rod, tie rod from ball joint bracket, ball joint from lower control arm, 4 lower ball joint set bolts, ball joint from suspension. Install is reverse but don't tighten the 4 lower ball joint set bolts.

torque is as follows:
ball joint to control arm- 112 ft-lbs
Tie rod nut- 67 ft-lbs
lower ball joint set bolts- 83 ft-lbs
remember to use a new cotter pin

Oct 08, 2008 | 2004 Toyota Tacoma

1 Answer

2003 suburban


Jack up the affected side and support vehicle on stands.
04ad7d8.jpg
Remove nut that fastens onto affected ball joint;
Using a "pickle fork" (ball joint separator) hammer fork in between ball joint. Use at least a 5 Lbs. mallet to strike fork;38722d9.jpg
(Above: Blue wire is holding rotor assembly from flailing away after ball joint separation).

Using ball joint extractor, press out failed ball joint:
12cbf07.jpg
0c5ef57.jpg

Then fit in new ball joint and reassemble rotor assembly.


Jun 18, 2008 | 2003 Chevrolet Suburban 1500

Not finding what you are looking for?
1990 Daihatsu Rocky Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...