Question about 1997 Mercury Mountaineer

Open Question

1997 mountaineer ,how to replace egr valve, find location

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

Ad
emissionwiz
  • 76846 Answers

SOURCE: OBD II code P1443

This code is usually caused by a loose gas cap or leaking gas cap cent diaphragm, the purge valve is under the car near the fuel tank

Posted on Nov 10, 2008

  • 92 Answers

SOURCE: 1997 Mercury Mountaineer

if the engine is a 4.6L the pcv will be on top and in middle of pass side valve cover.pull to remove.
if the engine is a 4.0L the pcv is located at the rear(firewall) of drivers side valve cover.this pcv has lock tabs holding it in,turn then pull to remove,the lock tabs are part of the valve cover so take care when removing not to harm tabs.

Posted on Nov 14, 2008

emissionwiz
  • 76846 Answers

SOURCE: DTC Code of a 1404 , and also a IAT High input malfunction

sounds like the IAT is disconnected, it is either in the flex hose from the air cleaner to the engine or in the air filter housing, on my GM product car it is in the air intake hose, it is small and has a 2 wire connector to it, just pushes and pulls in and out of the flexible air intake hose.

Posted on Mar 13, 2009

  • 2 Answers

SOURCE: where is the egr valve located on a 1997 mercury

follow the air filter vent up to the throttle body then look in back of aluminum housing

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 mountaineer 5 liter motor ,how to replace egr valve, find location


I have the 97 built in 96' (non DFTE) and the EGR valves is just to the left of the Transmission dipstick.
12_20_2012_2_10_04_am.jpg

May 13, 2012 | 1997 Mercury Mountaineer

1 Answer

Looking for diagram that shows egr valve on 97 nissan pickup


On page 6-6, Hanes #72030, you will find the diagram that shows the EGR Valve for models 1981 through 1984.The diagram also is followed by models 1985 through 1997. The valve works exactly the same in the 1997 as it does in the 1984. If you need a diagram online, follow this link;

http://www.nissanpartszone.com/diagrams/large/D21U/nissan-hardbody-pickup-1995-1997-egr-parts-147a001.png

Nov 15, 2010 | 1997 Nissan Pickup

1 Answer

Mercury Mountaineer sputters and backfires when climbing a hill


EGR Valve!
Do you have a MIL Light on? If so,what codes do you get?
Also,maybe a bad ignition coil

May 24, 2010 | 1997 Mercury Mountaineer

1 Answer

1997 mountaineer check engine light on again have already replaced all o2 sensors egr valve and a pressure something light kept comming on finally went out almost 400 miles later it has come back on


Assuming everything you replaced was bad,and I doubt it,you would have had a different code for each item you replaced!

What code do you have now?

It sounds as though,your replacing the parts, that are the symptom ,e.g. codes,not finding the cause or problem ,that set them.

May 16, 2010 | 2002 Mercury Mountaineer

2 Answers

Egr problem , 1997 mercury mountaineer 5 liter. egr system not a dpfe system, no egr tube, ports into the intake elbow. replaced egr valve egr postion sensor, checked the egr selonoid for resitance showed...


Check the passages under the airhorn. When carbon builds up the diagnostic blames the EGR for not opening and throws a code. Actually there is no flow to the EGR because the port is clogged and the diagnostic measures the flow after the EGR.

They really needed to have a sensor before and after the EGR. Also remember to disconnect the battery for 10 minutes to remove old info.

Sep 24, 2009 | 1997 Mercury Mountaineer

1 Answer

Where can I find a diagram of the locatation of the egr valve


Exploded view of the EGR valve mounting (3.1L engine)

cbef499.gif
EGR valve mounting arrangement (3.4L (VIN X) engine)

9aa9f4b.gif
View of the EGR valve mounting (3.8L engine)

5e4f2d5.gif

Jul 22, 2009 | 1997 Chevrolet Lumina

1 Answer

Where is the egr valve located on a 1997 mercury mountaineer.


follow the air filter vent up to the throttle body then look in back of aluminum housing

Jun 23, 2009 | 1997 Mercury Mountaineer

4 Answers

Code p1400 1997 nissan maxima


i just bought a Brand New EGRC Solenoid control valve but the code still there can anyone help , thank you so much.

Apr 14, 2009 | 1997 Nissan Maxima

1 Answer

No vacuum to egr valve


there is an EGR vacuum solenoid somwhere that controls on/off vacuum to actuate the valve. i am not to sure of the location, but follow the vacuum line back from the egr until you find a device that looks like an electrical check valve for vacuum. that is a possibilty. but then again i am a ford,chrysler guy and am just giving you an answer based on my understanding of the functuality of a vacuum egr system

Jan 15, 2009 | 1997 Nissan Pickup

1 Answer

1997 Mercury Mountaineer


if the engine is a 4.6L the pcv will be on top and in middle of pass side valve cover.pull to remove.
if the engine is a 4.0L the pcv is located at the rear(firewall) of drivers side valve cover.this pcv has lock tabs holding it in,turn then pull to remove,the lock tabs are part of the valve cover so take care when removing not to harm tabs.

Nov 14, 2008 | 1997 Mercury Mountaineer

Not finding what you are looking for?
1997 Mercury Mountaineer Logo

Related Topics:

740 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...