Question about Mercedes-Benz ML320

Open Question

I took my ml320 out. When i wanted to start it, it cranked a few times without starting. I soped it before it could finish. I tried starting again this time, no crank no starting. All the lamps in the dash come on but non was flickering. Start and Error message was displayed one after the other on the dash. I tried many times but it was the same problem. I went home and brought the spare but the problem remained

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2001 dodge dakota crank no start

Just had that problem w/ my 01 Dekota, it was the resistor that used to be mounted on the firewall and easy to get to but that is now mounted low on the back of the engine jammed into a bey tight position. I couldn't get to it myself, so ended up taking it to neighborhood garage. Cost me about $150

Posted on Apr 16, 2009

  • 14 Answers

SOURCE: 1998 honda accord does not start, no crank

CALL YOUR LOCAL DEALER!! there is a interlock update on the car... try that first.. but the the sensor in the shift might be bad.. you can unplug it to check if that's the problem it's under the center councel ... if your looking down at the shifter it's on the left side you can actual reach your had undter the plastic on the driver side and unplug it (by the carpet) just take out the one or two screws on the side by the carpet and i think it's a single wire up along the left side of the shifter...

Posted on Aug 21, 2009

  • 13 Answers

SOURCE: Randomly won't start, happened after jumping dead battery

Probably the battery. Take it the chain auto parts place and they will test it for you.

Posted on Aug 29, 2009

  • 4 Answers

SOURCE: Start Error Message when turn the key. No clicking, Dash normal.

seems like your key is not being recognized, possible your tumbler..the ring around your ignition switch is bad

Posted on Sep 21, 2009

  • 55 Answers

SOURCE: merc 308 sprinter non starter

Which sprinter 308 you have, 308 cdi or 308 D ? but sounds like sucking air, might be air lock

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My ml320 starts drives then speedo drops but engine ticks over no excelleration turn off then starts again noprobs this can happen 3/4/5 times while driving

my 2003 430 CLK CONVERTIBLE had a similar problem - started fine drove as far as you wanted to drive then wouldn't start again until 3 cycles of engine turn over and sometimes it would start driving 10 miles an hour when you least expect it! In my case, it was a camshaft sensor. There are 2. Only one of mine had failed. While I am handy, I was immediately over my head and took it to my excellent independent Mercedes repair shop. About a $250 repair.

Nov 08, 2016 | Mercedes-Benz Cars & Trucks

1 Answer

Starting problems with my ML320 Mercedes.

Replaced a crank sensor on a similar model. Easy to do.
See if tach moves when cranking.
If it is starting and not just cranking, then shutting off, sounds like it might be an ignition switch. On some models, the contacts for start are different than for run, Start ones are good and it starts, when key turns to run, it turns off. That would be my next move to test.

Jul 19, 2016 | Cars & Trucks

1 Answer

Starts fine runs fine. After turned off, will not start. Wait or try again and it starts. What's wrong?

Car will sometimes not start after warm. - CarGurus > Questions > Pontiac > Grand Prix

CarGurusJan 2, 2013 - When i start my car, for the first time during the day- I have no problem.... When I go somewhere and shut it off, sometimes it won't resatrt. ... I have to keep my foot on the gas and rev it up to keep it running- then it's fine. .... When your carstarts fine cold, then fails to restart while warm, it is usually a coolant ...

Blazer has to be jumped, then i shut it off and won't start. > Questions > Chevrolet > Blazer

CarGurusDec 21, 2013 - I jumped it and it ran fine, but as soon as I turned it off I couldn't start it again. No clicking just like the battery is drained. ... Then run the car for ten minutes and shut it off and if does not start, replace the battery. ... Blazer starts fine first time but after shutting off,has hard time starting-takes up to 10 key turns or ...

Engine Performance Problems Due to Crankshaft Position ... > Problems > Mercedes-Benz > ML320
"Crank no Start" Due to Failed Crankshaft Position Sensor on Mercedes-Benz ML320... It usually ocurs after I've turned the car off and try to restart after about 15 minutes. I typically allow it to ... fine. Stalling and starting problems intermittent at first, but now more frequent. ... Car runs fine then without out warning it won't start.

Jan 05, 2016 | Cars & Trucks

1 Answer

Cuts off at stops

Try cleaning the throttle valve.

Jul 06, 2017 | 2007 Mercedes-Benz ML320 CDI

1 Answer

1994 Bravada will not start after sitting idle for about 7 hrs

To clarify - are you saying it does not crank, or does not start ?
lt sounds like you are saying the engine will crank but not start, but then why would you need to jump the battery if that were true ?
If it cranks but does not start, have you checked fuel pressure with a gauge before and after cranking ? The fuel pressure could be low after sitting for a few hours if the check valve in the fuel pump is faulty.

Feb 28, 2014 | Oldsmobile Bravada Cars & Trucks

1 Answer

06 sorento timing

If the timing marks are dead on, the crank isn't going to be 180 off. I had one just like what you're dealing with. I replaced the crank sensor and the problem went away. I verified the signal with my scanner when it didn't want to start and sure enough, no rpm signal.

Jan 29, 2014 | Cars & Trucks

1 Answer

02 F250 V10 won't start

check the fault codes for a cam/crank position sensor problem

Jan 18, 2014 | Ford Cars & Trucks

1 Answer

Ford Taurus being a ********

Lets start at the beginning.
You say it cranks but will not start, right ?
The warning lights are supposed to come on with the key on and then go off once the engine starts.
If the engine cranks but will not start, someone will need to figure out if it is lacking fuel to the injectors or spark to the plugs, or something else. One way we check it is to look for spark at the plugs, check the fuel pressure, and try starting fluid in the throttle body.

Dec 08, 2012 | 1999 Ford Taurus

2 Answers

Mercedes ml320 dies out when going over bumps

Possible you have an earth wire loose ( contact wiring.) Loose battery terminals. Please start the checking from battery side and carefully not to cause any unexpected spark. That might cause a serious damage to ECU etc, My technical advise better a Car Electrician to do the job for your benefit.

Nov 24, 2017 | Mercedes-Benz Cars & Trucks

3 Answers

Need code ml320

Try the following website ..they supply unlock code for just 2.45$

Thank you!!...

Jul 31, 2008 | 1998 Mercedes-Benz M-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

77499 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides