Question about 2002 GMC Sierra C/K1500

Open Question

How long does it take to change a wiper motor

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 vw jetta wiper still not working after changing the wiper motor and wiper switch ? help


Did you check the fuse? Have power at the plug? could be a bad ground.

Dec 06, 2015 | Evan Cars & Trucks

1 Answer

2008 Ford Explorer Rear windshield wiper and wiper fluid stopped working


sounds like the wiper motor has worn out as was a steady decline , a wiper motor works by "tracks" that conduct the power , over time these wear thin until they no longer transmit the power , change the motor

Sep 22, 2015 | Ford Cars & Trucks

1 Answer

Wipers stuck in up position 09 toyota martix


If wipers do not work at all, and are stuck in one spot, check the fuse to see if it is bad. If wipers work, but stop facing up when you turn them off then the "park" portion of wiper motor has failed. If this is the case (wipers work and park up) then only fix is replace wiper motor. If fuse blown - replace it - and if it blows fairly soon after changing then something is binding wipers, or wiper motor is taking too much power and again, the motor needs changing.

Feb 24, 2015 | Toyota Cars & Trucks

1 Answer

How to change Windshield Wiper Motor Pulse Board on 2005 chevy impala


Change the wiper motor, and you replace the pulse board.. You can not buy the board separate from the motor.

Aug 07, 2014 | Chevrolet Chevy Cars & Trucks

1 Answer

How to change front wiper motor on 2004 Pacifica?


  1. Disconnect and isolate the battery negative cable.

110569875 Front Wiper Module - Remove/Install

  1. Remove the wiper module.

110569873 Front Wiper Motor Mounting

  1. With wiper module on bench, pry apart the socket and ball joint at the end of the bell crank .
  2. Remove the three front wiper motor mounting bolts and remove motor from module/linkage.
INSTALLATION
  1. Position the wiper motor into wiper module and install the three front wiper motor mounting bolts.
  2. Press the socket and ball joint together on end of bell crank.
  3. Install the wiper module.
  4. Connect the battery negative cable.
  5. Verify vehicle and system operation.
  6. Close hood.
11_29_2011_8_57_53_pm.gif11_29_2011_8_58_14_pm.gif

Oct 16, 2011 | 2004 Chrysler Pacifica

1 Answer

Directions on changing wiper motor. try wipers and hear motor run but wipers do not move. thx, chris


The wiper transmission has came off the motor. Very simple fix, just remove the wiper cowl, which is the plast vent covering the bottom of the windshield where the wiper arms are. hope this helps

Mar 15, 2011 | Hyundai Azera Cars & Trucks

1 Answer

Windshield wiper moter went out i need to change it out. how do i change it?


  1. Disconnect the negative battery cable.
  2. Remove both wiper arm and blade assemblies.
  3. Remove the cowl grille attaching screws and lift the cowl grille slightly.
  4. Disconnect the washer nozzle hose and remove the cowl grille assembly.
  5. Remove the wiper linkage clip from the motor output arm.
  6. Disconnect the wiper motor's wiring connector.
  7. Remove the wiper motor's three attaching screws and remove the motor. To install:
  8. Install the motor and attach the three attaching screws. Tighten to 60-85 inch lbs.
  9. Connect wiper motor's wiring connector.
  10. Install wiper linkage clip to the motor's output arm.
  11. Connect the washer nozzle hose and install the cowl assembly and attaching screws.
  12. Install both wiper arm assemblies.
  13. Connect the negative battery cable.

tecnovative_158.gif

Installing the wiper arm connecting clip.


tecnovative_159.gif

Feb 25, 2011 | 1992 Ford F250

1 Answer

I NEED TO CHANGE THE WIPER MOTOR ON MY 99 FORD EXPEDITION. I AM FAIRLY MECHANICAL, CAN I DO THIS WITH OUT TECHNIANS HELP?


The wiper motor replacement is not a difficult operation, just ensure connectors are firmly attached to the motor, and that wipers are working after installing the new motor.

Follow instructions on link below:

How to Change a Windshield Wiper Motor on a Ford Expedition

Jun 21, 2009 | 1999 Ford Expedition

1 Answer

Wipers


If your just changing the wiper blades, turn the wipers on and when they get to the top, take the key out. They dont move back much but its enough to change them. If you want to take the arms off, lift the hood up and use a 13mm socket or wrench to loosen the nut and then wiggle the arm off. If you need to change the motor, unclip the black molding that the wiper arms are on and you have full access to the motor.

Apr 16, 2009 | 2000 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...