Question about Mazda MX

1 Answer

My mazda e1600 jumps out of reverse after replcing the clutch and presher plate

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 111 Answers

Check that the linkages are connected corectly and are not fouled stopping the gearbox going all the way into gear. Also There is a posibility that you have gotten dirt of something betweeen the bell haouing and the back of the engine or the dowels are missing. This can cause a missalignment of the front shaft of the gearbox causing the gear contact to push each other away causing it to jump out of gear.

Posted on Apr 06, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The presher plate on my 97metro how will i know if it needs replacement


Well normally change both pressure plate and clutch disc together pressure plates do not give much trouble nearly always disc or bearing

Dec 07, 2015 | Cars & Trucks

1 Answer

Hard reverse engaugment


have you checked the hydraulic fluid chamber on the firewall close to the brake fluid area? If it is low the clutch plate may not be engaging for reverse gear.

Jun 09, 2014 | 2007 Mazda B4000

1 Answer

Ok I have a 1990 jetta the original tranny has lost 5th gear so I have got a tranny from the wreckers and installed a new friction disk. When I install the tranny with it bolted to the engine and the...


did you change your pressure plate some times pressure plate has installation clips ,that should be removed once plate is bolted up make sure also bell housings the same size

Feb 25, 2011 | 1990 Volkswagen Jetta

1 Answer

Mazda mpv 2000 no work reverse


Transmissions have a series of clutch plates, friction plates,bands,gears and solenoids located inside the transmission. As the vehicle moves forward, these plates operate similar to a clutch on a manual transmission, but using fluid pressure and momentum to do so. Usually these go bad due to lack of proper service intervals. If the fluid is not changed at recommended intervals, it breaks down, similar to engine oil,and causes the transmission to get hot and burn up these clutch plates and bands. Therefore you will get certain gears that will fail to engage. In your case, the reverse.

Oct 16, 2010 | 2000 Mazda MPV

2 Answers

How do I know when to replace the clutch on my 1999 Mazda Protege ES. Currently, it works, but I have to press the pedal all the way to the floor, with some force, to start the car. No check engine has...


whilst it works leave well alone ,when its slipping thats when you will need to replace the clutch,check the inhibitor switch on the clutch pedal though

Apr 16, 2010 | 1999 Mazda Protege

1 Answer

96 Mazda Protege is dead and has no power, wont turn over!


check all your fuses sometime when giving a jump start
a surge of power a cures and blows out the main fuse

Nov 14, 2009 | 1996 Mazda Protege

2 Answers

Mazda b2000 clutch slips when warm


This is a Common Problem after Replacement of a Clutch. After a Few Miles it is not Unusual to Have to have it Adjusted Again. I would take it back to whoever Fixed it and have them Adjust the Clutch.

Jan 15, 2009 | 1988 Mazda B2200

1 Answer

Stuck clutch pedal


you have a leak in the clutch hydraulic system. without the spring tension from the clutches pressure plate the the pedal wont return. it is likely that the leak is at the slave cylinder, which is inside the bell housing. to replace it the transmission must be removed.

Dec 14, 2008 | 1992 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...