Question about Dodge Dakota

1 Answer

I,ve run scanner through and code 11 appears, no ignition reference. What does this mean, Truck will not start after putting in new transmission, finding out sensor on back of motor broke, pulled tranny and replaced new sensor after re-installation. 1993 3.9l

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

Cam sensor

Posted on Apr 06, 2011

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have had a machine put on my Citroen C4 grand Picasso and it's come up with error codes P0925 & P0919 saying gear shift error, does this mean I need a new gear box?


code p 0919 refers to gear shift position control===causes wiring--- poor connections ---ECM---TCM
code p 0925 refers to gear shift reverse actuator --circuit /range performance ===causes --wiring---poor connection---gear shift reverse actuator---ECM---TCM
code p 1351 refers to IDM input circuit malfunction---ignition coil control , high voltage
there is nothing there to indicate a new transmission is required as the TCM ( transmission control module ) and reverse actuator or normally add on units and are separate to the box main
the wiring is always suspect as it hardens and breaks or the connections get corroded and do not pass power properly
I would at this stage not consider a new transmission and if it is suggested , I would get a second opinion from an accredit auto transmission specialist shop with experience on your vehicle

Oct 05, 2016 | Citroen Cars & Trucks

1 Answer

I have a 2005 land rover freelander in the engine fuse box the f3 fuse keeps blowing 15amp you start the truck go down the road fuse blows it starts runing ruff stop turn off truck then try to start wont...


15 amp is a fair current draw and for it to blow after a few minutes means that there is a short in that circuit that is allowing a drain to earth that just exceeds the 15 amp. It is in the ignition part of the system and may be a bad connection ( water ) or a problem appearing in the ECM or relay . Run fault codes to find the area of the fault. Because it is taking time to blow the fuse, it will be difficult to find. Check all wiring for rub marks .

May 07, 2014 | 2005 Land Rover Freelander

1 Answer

2000 GMC Envoy stalls while driving, shifting issues


Hi,
Yes, the Ignition switch is tied into the 'shift interlock system', and if the system is never really 'off' the codes may be related.

I'd REMOVE the remote start to ensure you're working from a 'clean slate' and get the ignition switch fixed....likely a dealer item, but call around auto parts stores. You may need to get it 'rekeyed' to match.

Also, a Jimmy and Envoy are identical - the Envoy is the higher trim line of the Jimmy: LINK

GL,
Td

Oct 10, 2012 | 2000 GMC Envoy

1 Answer

Jimmy stalls while driving, shifting issues


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems.


Oct 10, 2012 | 2000 GMC Jimmy

2 Answers

Code 11. what do i check?


11 camshaft signal or ignition signal, no reference signal during cranking
If you replace the CKP sensor (crankshaft position) you will more than likely cure the problem, I'll assume you have an intermittent engine stall out or hard not start?

Nov 03, 2011 | 1995 Dodge Neon

1 Answer

1996 dodge dakota 3.9 engine quit running when we do the ignition test it gives us a code of 1255 what would that mean. It will run if we put gas down the carb.


i`m not sure what the code meaning is but if you put gas down the throttle body and it runs then you have a fuel problem which this code may refer to.this year of truck is fuel injected throttle body.it could be a fuse,fuel pump relay,fuel pump,plugged fuel filter,stuck open fuel pressure regulator not building enough pressure,wiring for fuel or pump system or even a computer(ecm) problem.

Apr 21, 2011 | Dodge Dakota Cars & Trucks

2 Answers

96 Jeep Cherokee Country will turn over fine will not start. engine light code is 121155


- Code 12, recently battery unplugged

- Code 11 Ignition reference signal
No ignition reference signal detected during cranking (bad Hall effect) OR loss of camshaft sensor (and, for cars with crankshaft sensors — which does not include the 2.2/2.5 — timing belt skipped a tooth or loss of crankshaft sensor).

Note #8 Can cause the engine to stop working entirely with no limp-home mode. Note: An anonymous poster wrote, “Code 11 will only be set upon clearing the codes, most commonly by disconnecting the battery. It says in the factory diagnostic manuals that code 11 means no ignition reference signal has been seen since battery disconnect. As soon as the vehicle's engine is cranked, and a reference signal is seen, code 11 will go away immediately on it's own. It also won't be set upon failure of a part such as a hall-effect pick-up plate, or loss of the timing belt. If no reference signal is seen during cranking after a battery disconnect, code 11 will remain. This is a helpful indicator in a no-start condition.” (Chrysler did sometimes change codes depending on the year, so it may be that some of these apply to differentyears).

- Code 55 End scan test

Check other details HERE.

Hope help with this, remember rated this help.

May 26, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

Its not starting as good as it used to


Try running Chevron Techron concentrated fuel injector cleaner in a 1/4 tank of gas.

Also, may be the issue in this TSB.

LIGHT TRUCK: 1990-91 RANGER
1991 EXPLORER
ISSUE: A hard start or no start condition may occur when the engine is cold. The engine may not start without cycling the key to the OFF position and back to START. Ignition switch bounce (loss of electrical continuity between contacts) may cause the EDIS module to recycle several times or to lock-up and not allow a start at all.
ACTION: Install a new ignition switch containing synthetic lubricant which reduces the amount of bounce. Also, install a new wiring connector containing a new material that is compatible with the new synthetic lubricant. Refer to the following procedure for service details.
REMOVAL
  1. Disconnect the battery power.
  2. Remove the trim panel. Refer to the 1990-91 Ranger/Explorer Shop Manual, Section 11-04B, for removal procedure.
  3. Turn the lock cylinder to the RUN position.
  4. Remove the two (2) nuts on the ignition switch.
  5. Separate the connector from ignition switch by gently prying on the ears of the connector and pulling apart firmly.
  6. Disengage the terminals from the existing connector. Discard the connector.
  7. Insert terminal into proper locations in new connector (F2TZ-14489-A), Figure 1. INSTALLATION
    1. Remove the spring clip from the new switch (F2TZ-11572-A). This clip keeps the switch in the correct position during shipment.
    2. Press the new connector (F2TZ-14489-A) onto the terminals of the ignition switch. Be sure the tabs lock securely.
    3. Locate the switch on the weld studs on the steering column. NOTE: THE END OF THE ACTUATOR ROD MUST FIT IN THE HOLE ON THE SLIDER.
    4. Install the nuts on the weld stud. Tighten to 4.45-7.24N-m (39-64 lb-in).
    5. Connect the battery terminal.
    6. Check the switch operation. If necessary, adjust it. Refer to the 1990-91 Aerostar, Explorer, Ranger Truck Shop Manual, Section 11-04B, for adjustment procedure.
    7. Install the trim panel.

    PART NUMBER PART NAME F2TZ-11572-A Ignition Switch F2TZ-14489-A Wiring Connector

Nov 12, 2009 | 1991 Ford Explorer

2 Answers

Engine check light


It means that it didn't receive a signal from the transmision module.
Have your transmission control module checked.

To reset your engine codes:
Remove the negative terminal of your battery (10mm wrench).
Turn your ignition key to START and hold it there for about 15 seconds.
Turn your ignition key to OFF and remove it.
Connect the negative terminal of your battery.

TCM (Trans control Module)
(electronic transmission control module)

Jan 09, 2009 | 2000 Dodge Dakota Quad Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...